PerkinElmer Spotlight 400 Series Скачать руководство пользователя страница 79

Страница: 79 / 120

Techniques for Collecting IR Images and Spectra . 79

ATR Objective Specification

The ATR cassegrain is fitted to the imager and the ATR crystal holder is supplied separately.

ATR crystal materials

Germanium or Silicon

Range of measurement

Ge: 5500 cm

−1

to 600 cm

−1

Si: 7800 cm

−1

to 800 cm

−1

Area of contact with sample

Nominally 100 µm diameter flat surface. Single internal reflection from surface.

Maintenance

The ATR assembly may be removed (see

Removing the ATR Crystal Holder from the Imager

on page 85), cleaned (see

Cleaning the ATR Objective Crystal

on page 87), or replaced and

aligned by the user (see

Fitting the ATR Crystal Holder to the Imager

on page 80).

A replacement crystal is provided with each objective.

Содержание Spotlight 400 Series

























































































































Результаты поиска

Содержание Spotlight 400 Series

Отзывы:

Похожие инструкции для Spotlight 400 Series

Бренды по названию

Популярные бренды

PerkinElmer Spotlight 400 Series, Руководство пользователя

Результаты поиска

Содержание Spotlight 400 Series

Отзывы:

Похожие инструкции для Spotlight 400 Series

Бренды по названию

Популярные бренды