background image

IC-03.1 Card Capture Reader 

19 

1.  Set  the  card container into  operating  position,  to do so  set  its  lower  end  into  the 

card  capture  reader  with  a  slight  inclination  and  then  give  it  a  vertical  position; 
correct installation of the container does not require much effort. 

2.  Turn the key in the lock all the way (

close 

the lock); after the lock closing the panel 

should lean tightly on the card capture reader’s framework (2) without distortions. 

3.  When necessary to continue operation of the card capture reader switch on its 

power supply. 

11 TRANSPORTATION AND STORAGE 

The card capture reader  in the original package should be transported only in closed 
freight containers or other closed type cargo transport units. 

During storage and transportation the boxes can be stacked no more than 5 layers high. 

The card capture reader should be stored in dry indoor facilities at ambient temperatures 
between –40°C and +45°C and at relative air humidity of up to 98% at +25°C. The storage 
room should be free from vapors of acids, alkalis, and gases that cause corrosion. 

After transportation or storage at below-zero temperatures or high air humidity, the card 
capture reader should be kept unpacked for no less than 24 hours under normal climate 
conditions (see Chapter 2) prior to install. 

12 

TROUBLESHOOTING

 

Possible faults to be corrected by the customers themselves are listed in Table 5. 

For faults not listed in Table 5 we advise to consult PERCo Technical Support Department. 

Table  5.   Possible failures and troubleshooting 

Fault

 

Probable cause

 

Remedy

 

Power supplies are on, but the card 

capture reader does not function, the 

LED indicators are off 

Faulty connection or breakdown 

of power supply cable (10). 

Faulty power supply unit. 

Replace the cable (10). 

Replace the power supply 

unit. 

The LED indicators are on but the 

card capture reader is not controlled 

by the ACS controller 

Faulty connection or breakdown 

of connection cable (11) of the 

ACS controller  

Replace the connection 

cable (11) 

13 MAINTENANCE 

Maintenance of the card capture reader during operation is reduced to periodic cleaning of 
its  outer surfaces.  To remove dirt it  is recommended to use  liquid cleaners  without 
abrasives containing ammonia. 

 

Содержание IC-03.1























Отзывы: