Pentair Siata V132 SFE Скачать руководство пользователя

Страница: 50 / 88

Installer manual Siata V132 - SFE - Programming

50 / 88

Ref. MKT-IM-003 / B - 19.04.2017

Chlorine driver activated

Set the chlorine driver on or off.

Use

and

to edit this parameter.

Press

to validate and switch to the next parameters.

Note



This functionality only works if the controller has chlorine driver.

Volume restored / not restored

Set to determine whether the volume is restored (UlMM) or not
restored (UdlF). The volume remaining will be kept in memory or
restored to the programmed value, after exiting the programming

(SH:01 or SH:02).

Use

and

to edit this parameter.

Press

validate.



"End" is displayed on the screen. Programming is now
complete.

6.3.1. Statistics

The statistics menu displays some of the module's historical data.. To access to this menu, press and

hold

for 5 seconds.

•

The treated volume is displayed on a running string to allow a number greater than 9999 to be
read;

•

Use

to switch to the next parameters in the statistics menu;

•

The date and time information for the last regenerations is only available if they have been
carried out;

•

While the statistics are displayed, the regeneration icon is on, if not otherwise indicated;

Data

Description

Xxxx

Number of regenerations carried out.

SAxx

Number of residual regenerations before the salt alarm is generated.

FFxx

Number of days elapsed since the last regeneration.

Lxxxxxx

Overall volume treated [l].

Xx:xx

Day and time of the last regeneration carried out, the regeneration icon is on.

Xx:xx

Day and time of the second last regeneration carried out, the service icon is on.

Xx:xx

Day and time of the third last regeneration carried out, the service and
regeneration icons are on simultaneously.

End

End of the statistics.

189x

Software release and revision.

Содержание Siata V132 SFE

























































































Результаты поиска

Содержание Siata V132 SFE

Отзывы:

Похожие инструкции для Siata V132 SFE

Бренды по названию

Популярные бренды

Pentair Siata V132 SFE, Руководство по установке

Результаты поиска

Содержание Siata V132 SFE

Отзывы:

Похожие инструкции для Siata V132 SFE

Бренды по названию

Популярные бренды