Pentair Riversoft Скачать руководство пользователя страница 2

Страница: 2 / 90

Installer Manual Riversoft - Table of content

2 / 90

Ref. MKT-IM-045 / A - 13.03.2020

Table of content

Generalities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1.

Scope of the documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2.

Release management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3.

Manufacturer identifier, product . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4.

Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.5.

Abbreviations used and glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.6.

Norms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.6.1.

Applicable norms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.6.2.

Available certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.7.

Procedure for technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.8.

1.9.

Limitation of liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.10.

Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1.

Safety pictograms definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2.

Serial and safety tags location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3.

Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3.1.

Personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3.2.

Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3.3.

Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.

Hygiene and sanitization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.4.1.

Sanitary issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.4.2.

Hygiene measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.1.

Introduction to softeners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.1.1.

Softening principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.1.2.

System service & regeneration cycles (8-cycles operation) . . . . . . . . . 14

3.2.

Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.2.1.

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.2.2.

Performance flow rate characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.3.

Outline drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.4.

Description and components location . . . . . . . . . . . . . . . . . . . . . . . 21

3.5.

Softener’s available options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.5.1.

Safety brine valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.1.

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.2.

Safety notices for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Содержание Riversoft



























































































Результаты поиска

Содержание Riversoft

Отзывы:

Похожие инструкции для Riversoft

Бренды по названию

Популярные бренды

Pentair Riversoft, Руководство по установке

Результаты поиска

Содержание Riversoft

Отзывы:

Похожие инструкции для Riversoft

Бренды по названию

Популярные бренды