Pentair Riversoft Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 90

background image

Installer Manual Riversoft - Installation

34 / 90

Ref. MKT-IM-045 / A - 13.03.2020

•

The diagrams above illustrate how the flexible piping connection should be mounted;

•

in order to adequately compensate the tank elongation the flexible tubes must be installed
horizontally;

•

should the flexible piping connection be installed in vertical position, instead of compensating
the elongation, it will create additional stresses on the valve & tank assembly. Therefore this is
to be avoided;

•

the flexible piping connection must be also be installed stretched, avoiding excessive length. For
instance 20 - 40 cm is enough;

•

excessively long and non-stretched flexible piping connection will create stresses on the valve
and tank assembly when the system is pressurized, as illustrated in the below picture: on the left
the assembly when the system is unpressurised, on the right the flexible piping connection when
put under pressure tends to lift up the valve when stretching up. This configuration is even more
dramatic when using semi-flexible piping;

•

failure to provide enough vertical compensation may lead to different kinds of damage, either on
the valve thread which connects to the tank, or on the female thread connection of the tank that
connects to the valve. In some cases, damage may also be seen on the valve inlet and outlet;
connections.

•

in any case, any failure caused by improper installation and/or piping connections may void the
warranty of Pentair products;

•

in the same way, using lubricant* on the valve thread is not allowed and will void the warranty for
the valve and tank. Indeed using lubricant there will cause the valve to be over-torqued, which
may lead to valve thread or tank thread damage even if the connection to piping has been done
following the above procedure.

*Note: Use of petroleum-based grease and mineral based lubricant is totally forbidden, not only on the valve thread, since

plastics (especially Noryl) will highly suffer from contact with this type of grease, leading into structural damage hence to

potential failures.

Bypass configuration

Manifold configuration

«
...
32
33
34
35
36
...
»

Содержание Riversoft



























































































Отзывы:

Нет отзывов

Похожие инструкции для Riversoft

Бренд: Rheem Страницы: 15

Electraflow Plus

Бренд: PC Cox Страницы: 2

Бренд: DORAL Страницы: 8

Бренд: A.O. Smith Страницы: 43

Бренд: lancer Страницы: 6

Бренд: YATO Страницы: 56

Бренд: Promek Страницы: 23

Бренд: Raypak Страницы: 57

Бренд: Talent Страницы: 28

Бренд: Zenith Страницы: 8

Double Bubbler LF SCWT14CB Series

Бренд: Halsey Taylor Страницы: 6

TTW Eco-Defender

Бренд: Bradford White Страницы: 52

Бренд: Adhesive Dispensing Страницы: 12

HIGH EFFICIENCY ATMOSPHERIC VENTGAS WATER...

Бренд: A.O. Smith Страницы: 40

Бренд: Murdock Страницы: 9

Бренд: JOWA Страницы: 36

Micro X-Pure WP3922

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды