manualshive.com logo in svg

Pentair raychem ngc-30/uit2, Руководство по программированию

Поделиться
Скачать
Pentair raychem ngc-30/uit2 Скачать руководство пользователя страница 6

6 / 84

industrial heat tracing solutions

EN-RaychemNGC30UIT2Programming-AR-H58186      02/16

1.1.6  CommuniCations

The NGC-UIT2 units can be networked to a host PC running Windows®-based Raychem 

Supervisor client-server software for central programming, status review, and alarm 

annunciation. NGC-UIT2s support the Modbus

®

 protocol and are available with an RS-232, RS-485 

or 10/100Base-T Ethernet communication interface.

1.1.7  ComPLete system

The Raychem NGC-30 is supplied as a complete system ready for field connections of power 

wiring and temperature sensor input. Optional Power Distribution further enhances the reduction 

of field wiring and labor to install.

1.1.8  the raychem nGC-uit2-eX ProGramminG Guide

This Raychem NGC-UIT2-EX Programming Guide (H58186) assists in the set up and operation of 

the Raychem NGC-20 and NGC-30 system.
The Raychem NGC-UIT software (version 4.x and higher), installed in the NGC-UIT2-EX (User 

Interface Terminal), is designed to configure various Raychem devices. 
This software version supports the: 
1) Raychem NGC-20 controllers
2) Raychem NGC-30 Heating-Tracing Panels using:
     a) NGC-30-CRM/-CRMS card rack modules with or without multiplexed RTD inputs via the    

 

Raychem RMM2 module or RTD inputs via the Raychem PLI module.

     b) MONI-RMC and RMM-DI modules for digital input and relay output signals.
It supports the RMC modules and RMM-DI for digital inputs and outputs as well. 
The software provides several features to help configure and maintain the Raychem devices. This 

document is not intended to provide detailed explanations of the specific features of each product, 

but rather to show how to access various parameters within the devices using the Raychem NGC-

30 software. Please refer to specific detailed product use documentation:
•  Raychem NGC-30 Installation Manual (H57878)
•  Raychem NGC-UIT2 Modbus Protocol Interface Mapping for NGC-30 Systems (H57880).

1.1.9  user interFaCe terminaL (nGC-uit2) LanGuaGes

The languages supported by the NGC-UIT2 display are - and not limited to -: English, Spanish, 

French, German, Russian, Chinese, Italian and Czech. The display language is selected by 

accessing the System|Misc. screen. Refer to section 3.3.31 System | Misc Window  on page 60 for 

additional information.

1.2   VitaL inFormation

This manual is a guide for the setup and operation of the Raychem NGC-30 and NGC-20 in 

combination with the NGC-UIT2-EX user interface.
Important: All information, including illustrations, is believed to be reliable. Users, however, 

should independently evaluate the suitability of each product for their particular application. 
Pentair Industrial Heat Tracing Solutions makes no warranties as to the accuracy or completeness 

of the information, and disclaims any liability regarding its use.
Pentair Industrial Heat Tracing Solutions only obligations are those in the Pentair Industrial Heat 

Tracing Solutions Standard Terms and Conditions of Sale for this product, and in no case will 

Pentair Industrial Heat Tracing Solutions or its distributors be liable for any incidental, indirect, or 

consequential damages arising from the sale, resale, use, or misuse of the product. Specifications 

are subject to change without notice. In addition, Pentair Industrial Heat Tracing Solutions 

reserves the right to make changes—without notification to Buyer—to processing or materials 

that do not affect compliance with any applicable specification.

Содержание raychem ngc-30/uit2





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды