Pentair Evolio 255 10 Скачать руководство пользователя

Страница: 73 / 90

Installer manual Evolio 255 740-760 - Maintenance

Ref. MKT-IM-037 / D - 25.10.2021

73 / 90

8.5.7.5

Top plate and disc valve/flappers replacement

1. Remove the softener and valve covers, see Covers removal (softener and valve) [

→

Page 62].

2. Remove the motor and camshaft, see Optical sensor replacement [

→

Page 76].

CAUTION

Beware of sharp edges when unmounting the flapper spring.

Use of protective glove is highly recommended to remove the spring

(3)

3. Using a flat screwdriver, release the flapper springs (2) one by one and then remove the

spring

(3)

4. Loosen all top plate screws

(1)

5. Remove the top plate

(4)

from the valve.

6. Clean or replace the flappers

(7)

if needed.

Info

The outline of the flapper seat can be seen on the flapper side.

If the outline is irregular, this may indicate that debris is or has been preventing the
flapper

(7)

from closing, and potential damages.

7. Remount flappers

(7)

CAUTION

Flapper 6 is asymmetrical.

Failure to insert it properly will cause permanent leakage to drain.

8. Once all flappers

(7)

are back in place, position the top plate

(4)

and screw it back following

the figure order.

9. Position the one-piece spring

(3)

back to its place, locking it on its mounting pin

(5)

and pads

(6)

10. Using a small flat screw driver, push on each part of the spring

(2)

to clip it back into the

flappers

(7)

lever.

11. Remount the motor and camshaft, see Optical sensor replacement [

→

Page 76].

12. Remount the softener and valve covers, see Covers removal (softener and valve) [

→

Page 62].

Содержание Evolio 255 10



























































































Результаты поиска

Содержание Evolio 255 10

Отзывы:

Похожие инструкции для Evolio 255 10

Бренды по названию

Популярные бренды

Pentair Evolio 255 10, Руководство по установке

Результаты поиска

Содержание Evolio 255 10

Отзывы:

Похожие инструкции для Evolio 255 10

Бренды по названию

Популярные бренды