Pentair Evolio 255 10 Скачать руководство пользователя

Страница: 30 / 90

Installer manual Evolio 255 740-760 - Installation

30 / 90

Ref. MKT-IM-037 / D - 25.10.2021

Materials:

• softener;

• pipes;

• Teflon

tape;

• grounding straps (optional);

• overflow pipe ½";

• valve drain pipe ½".

Material included:

• by-pass.

4.5.4

Inspection/preliminary assembly

4.5.4.1

Inspection

Mandatory

Any missing or faulty equipment must be specified on the transport documents. Notify
the transporter company and supplier immediately.

Info

In some case, some damage can only be observed when commissioning the softener.

Check that all delivered equipment corresponds to the shipping list and that it is not damaged.

4.5.4.2

Preliminary installation

Info

This softener doesn’t need any preliminary assembly.

4.5.5

Softener installation

1. Shut off power or fuel supply to water heater, see manufacturer’s instructions.

2. Shut off all water at main supply water line.

3. Open highest and lowest faucet of the line where softener will be installed to relieve pressure

and drain the system.

4. Set the unit in place, see Softener connection to piping [

→

Page 27] and Installation layout

[

→

Page 29].

5. Place the softener in a firm concrete floor or slab base. Be sure the unit is reasonably level.

CAUTION

Do not shim the softener directly for levelling. If necessary to shim, fabricate a
platform base to set the tank on and then shim under the platform base.

6. Make necessary piping changes for connecting the softener inlet and outlet to the home

piping. Make sure not to reverse inlet and outlet.

Содержание Evolio 255 10



























































































Результаты поиска

Содержание Evolio 255 10

Отзывы:

Похожие инструкции для Evolio 255 10

Бренды по названию

Популярные бренды

Pentair Evolio 255 10, Руководство по установке

Результаты поиска

Содержание Evolio 255 10

Отзывы:

Похожие инструкции для Evolio 255 10

Бренды по названию

Популярные бренды