pellenc EXCELION 2 LH Скачать руководство пользователя страница 8

Страница: 8 / 84

BRUSH CUTTER EXCELION 2 LH

53_154421-A

Note

The term “Residual Current Device” (RCD) can be replaced by “Ground Fault Circuit Interrupter” (GFCI) or

“Earth Leakage Circuit Breaker” (ELCB).

2.1.3. PERSONAL SAFETY

Stay alert, watch what you are doing, and use common sense when operating the power tool. Do not

use a power tool while you are tired or under the influence of drugs, alcohol or medication.

A moment

of inattention when using a power tool can result in serious personal injury.

Use personal protective equipment. Always wear eye protection.

Safety equipment such as dust masks,

non-slip safety shoes, helmets, or ear protection used at the appropriate times reduces injuries.

Avoid accidental starting of the tool. Make sure the switch is in the off position before you connect the

tool to the power source and/or battery pack, pick it up, or carry it.

Carrying a power tool with your finger

on the switch or connecting a power tool with the switch in the ‘on’ position can cause accidents.

Remove any adjusting wrench before switching the electric tool on.

A wrench left attached to a rotating

part can cause injury.

Do not rush. Keep proper footing and balance at all times.

This provides better control of the power tool

in unexpected situations.

Dress appropriately. Do not wear loose clothing or jewellery. Keep hair and clothing away from moving

parts.

Loose clothes, jewellery or long hair can get caught in moving parts.

If devices are provided for connecting dust extraction and collection equipment, ensure that these are

connected and properly used.

Use of dust collection can reduce dust-related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool

safety principles.

A careless action can cause severe injury within a fraction of a second.

2.1.4. POWER TOOL USE AND CARE

Do not force the power tool. Use the power tool suited for the job.

The adapted power tool does the work

better and more safely at the speed it was built to operate at.

Do not use the power tool if the switch does not allow it to be switched on and off.

Power tools that

cannot be controlled by a switch are dangerous and must be repaired.

Unplug the tool from the socket or remove the battery (if possible) before any adjustment, change of

accessory or storage.

These preventive safety measures reduce the risk of accidentally starting the power

tool.

When not in use, keep power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate it.

Power tools are dangerous when operated by inex-

perienced users.

Maintenance of the power tool and its accessories is mandatory. Check that the moving parts are not

out of alignment or jammed, that there are no broken parts or that there is no other condition which

could affect the operation of the power tool. If damaged, repair the power tool before using it.

Many

accidents are due to poorly maintained power tools.

Keep the cutting elements sharp and clean.

Properly maintained cutting tools with sharp cutting elements

are less likely to jam and are easier to control.

Use the power tool, accessories, blades, etc. in accordance with these instructions, taking into account

the working conditions and the work to be done.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

Handles and gripping surfaces must be kept dry, clean and free from oils and grease

. Slippery handles

and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

2.1.5. BATTERY TOOL USE AND CARE

Recharge only with the charger specified by the manufacturer.

A charger that is suitable for one type of

battery pack may create a risk of fire when used with another battery pack.

Use power tools only with specifically designated battery packs.

Use of any other battery packs may

create a risk of injury and fire.

Содержание EXCELION 2 LH





















































































Результаты поиска

Содержание EXCELION 2 LH

Отзывы:

Похожие инструкции для EXCELION 2 LH

Бренды по названию

Популярные бренды

pellenc EXCELION 2 LH, Руководство пользователя и инструкции по эксплуатации

Результаты поиска

Содержание EXCELION 2 LH

Отзывы:

Похожие инструкции для EXCELION 2 LH

Бренды по названию

Популярные бренды