pellenc EXCELION 2 LH Скачать руководство пользователя страница 37

Страница: 37 / 84

BRUSH CUTTER EXCELION 2 LH

53_154421-A

1. Install the battery and the power cord on the har-

ness, refer to the assembly sheet supplied with the

harness.

2. Check that the power cord is properly connected.

3. On the right chest strap of the harness, connect

the adapter cord (reference 57238 for 750 battery,

57248 for Alpha 520 battery) to the quick connector

of the power cord (19) of the Brush cutter.

4.7. DISCONNECTING THE BATTERY

1. Switch off the tool (refer to Section 5.1.2, “Stopping

the tool”).

2. On the right chest strap of the harness, disconnect

the adapter cord from the quick connector of the

power cord (19) of the Brush cutter.

3. To remove the battery from the harness, refer to the

battery instructions and to the harness assembly in-

structions

4.8. ADJUSTING THE WORKING POSITION

Important

Take the time to properly adjust your harness and machine. This will guarantee your ease of use and prevent

any discomfort.

Before use, the working position of Brush cutter Excelion 2 LH must be adjusted according to the size of the user.

4.8.1. ADJUSTMENT OF THE HARNESS AND FITTING OF THE CARRYING STRAP

Adjusting the length of the harness makes it possible to adjust the "vertical position" of the Brush cutter Excelion

2 LH. This adjustment goes hand in hand with the adjustment of the balancing of the machine and the adjustment

of the round handle.

To consult the procedure for adjusting your harness, refer to the assembly sheet supplied with it.

Содержание EXCELION 2 LH





















































































Результаты поиска

Содержание EXCELION 2 LH

Отзывы:

Похожие инструкции для EXCELION 2 LH

Бренды по названию

Популярные бренды

pellenc EXCELION 2 LH, Руководство пользователя и инструкции по эксплуатации

Результаты поиска

Содержание EXCELION 2 LH

Отзывы:

Похожие инструкции для EXCELION 2 LH

Бренды по названию

Популярные бренды