–SOURCE: for CH1 to CH8 the user can select between LINE and MIC
for CH9 to CH12 the source is fixed to LINE
for CH13 to CH16 the user can select either LINE and USB if the ANALOG-EXTENSION CARD is
installed, or either DANTE and USB if the DANTE-EXTENSION CARD is installed.
–GAIN: if the Source is LINE the gain range is -/+18dB, if the Source is MIC the gain range is from +10dB to
+46dB, (step 0.5dB).
The gain can be changed in three different ways:
a. input the value on the text-box and press Enter
b. click with the mouse on the Up/Down button
c. click and hold the Left mouse button on the text-box and move the mouse up/down to increase or decrease the
value
–DELAY: From 0ms to 15ms (step 0.05ms), to edit the value use the same procedure used on the Gain
–GATE: To use the Gate, the user must first turn the function on by clicking the On/Off button. When On, the
button will turn Orange. The parameters for the Gate are Threshold (from -80dBfs to -50dBfs, step 5dB), Release
Time (from 1ms to 1sec, step not linear), Attack Time (from 1ms to 1sec, step not linear) and Hold Time (from
0ms to 10sec, step 50ms).
–CMP: to use the Compressor, the user must first turn the function on by clicking the On/Off button. When
On, the button will turn Orange. The parameters of the compressor are Threshold (from -30dBfs to 0dBfs,
step 0.2dB), RATIO (from In 1:Out 1 to In 32:Out 1), Knee (from 0% Hard Knee to 100% Soft Knee), RE-
LEASE-TIME (from 1ms to 1sec, step not linear), Attack (from 1ms to 1sec, step notlinear).
–HP Filter: The input High Pass Filter is a 2nd order Butterworth filter. First turn the function on by clicking the
On/Off button. When On, the button will turn Orange. When enabled, the user can input the frequency value
(range from 20Hz to 20kHz, step 1Hz).
–PST MUTE: Post Fader Mute (OFF/ON, when ON the button is red)
–FBK ELIM (Feedback Eliminator): The system offers 2 feedback eliminators for the first 8 channels. When the
FBK Elim are used on two channels the other 6 channels can’t use the Fbk Elim, i.e if the FBK Elim1 is used on
CH.3 and FBK Elim2 is used n CH.4 then if the user tries to set the Fbk Elim1 on CH.1 then the system show a
pop-up with the following message:“ Feedback Eliminator 1 already assigned to Input CH.3” In the Input Sec-
tion, the user can only assign the Feedback eliminator to the CH but to enable or disable the “Engine” the user
must go on the Edit Section of the FBK ELIM. from the Top Edit menu.
–EQ Enable: when disabled (button greyed out) the EQ is bypassed and the filter can not be edited.
–4 EQ Filters: the Eq filters are operative only when the EQ Enable is ON (button is orange color).The single fil-
ters can also be enabled or disabled using the relative ON/OFF button. Each filter type can be set as Peak (BELL)
or “Hi-Shelving” or “Lo-Shelving”, the frequency can be set to a range of 20Hz-20kHz step 1Hz, the Gain of the
filter can be changed to a range of +/-12dB and the Q factor of the filter can be changed from 0.3 to 20.
Each filter is shown on the graphic and when the filter is enabled the user can modify the frequency and Gain us-
ing the mouse directly on the graphic. Click and hold the left mouse button on the squared point on the graphic
(one color per filter) and move the mouse up/down to change the gain and Left/Right to change the frequency.
