Peavey AQ 12 Скачать руководство пользователя страница 2

FCC CAUTION:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) 

This device may not cause harmful interference, and (2) this device must accept any interference received, 

including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void 

the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pur-

suant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harm-

ful interference in a residential installation. This equipment generates, uses and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to correct the interference 

by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

—Consult the dealer or an experienced radio/TV technician for help.

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment, 

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 

The equipment should be installed and operated with minimum distance 20cm between the radiator and 

your body.

IC WARNING:

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the fol-

lowing two conditions: (1) this device may not cause interference, and (2) this device must accept any inter-

ference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de 

licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de 

brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le 

brouillage est susceptible d’en compromettre le fonctionnement.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

the device is compliance with RF exposure guidelines, and the equipment should be installed and operated 

with minimum distance 20 cm between the radiator and your body.

l’appareil est conforme aux directives d’exposition RF, et l’équipement doit être installé et exploité avec une 

distance minimale de 20 cm entre le radiateur et votre corps.

Содержание AQ 12





















Отзывы: