Peavey AQ 12 Скачать руководство пользователя страница 12

Disconnecting AC Power to the AQ™12

We recommend that the Power switch (3) be used to turn the unit off first, and then the AC power cord can be 

removed, this minimizes stress to the power amplifiers and the transducers from turn-off transients.  The pow-

er switch has an arc suppression capacitor to help during turn-off, and tends to make a clean disconnect from 

the AC power, while the power cord IEC connector can make intermittent contact before finally becoming fully 

disconnected, e.g., as when wiggling the cord.

EQ Presets

There are a number of Factory defined Presets quickly available to the user via the Preset Selector Switch (13). 

Here is a listing of those Presets:

VOICE

ACOUSTIC

MONITOR

PRGM MUSIC

DJ

LIVE MUSIC

Here is a brief description of what each Preset does to the nominally flat response of the speaker system:

VOICE Preset

Filters out the low and high frequencies outside the normal voice bandwidth to reduce booming or sibilance, and 

provides a mild presence boost to help with intelligibility. 

ACOUSTIC Preset

This Preset provides a nominally flat frequency response, within the limits of the systems drivers and nearby 

acoustic environment.

MONITOR Preset

Mild low-shelf cut to account for the floor location, mid-bass EQ to counter the floor bounce notch, and mild 

presence boost for vocals, very slight roll-off of extreme high frequencies to minimize hash.

PRGM MUSIC Preset

This Preset is intended for use with recorded music, with a mild bass-boost, a slight upper mid-bass emphasis for 

punch, and some high frequency boost with subsequent extreme high frequency taper off.  Dynamic bass boost 

employed.

DJ Preset

Provides maximum bass boost, with some EQ for punch and presence, with some high frequency boost with 

subsequent extreme high frequency taper off.

Dynamic bass boost employed.

LIVE MUSIC Preset

Very mild bass boost, with mild EQ for punch and presence, with some high frequency boost with subsequent 

slight extreme high frequency taper off.

Dynamic bass boost employed.

Содержание AQ 12





















Отзывы: