manualshive.com logo in svg

Peak IPEH-004005-J, Руководство пользователя

Поделиться
Скачать
Peak IPEH-004005-J Скачать руководство пользователя страница 24

MU-Thermocouple1 CAN FD – User Manual 
 

24 

6.2

 

Internal Termination 

The CAN bus termination for the CAN connection can be set with 
the 

switch block

 on the board. By default, the switch is set to 

off

. 

Tip:

 We recommend adding termination at the CAN cabling, for 

example with termination adapters (e.g. PCAN-Term). Thus, 
CAN nodes can be flexibly connected to the bus. 

Do the following to activate the termination: 

Attention!

 Electrostatic discharge (ESD) can damage or destroy 

components on the card. Take precautions to avoid ESD. 

1.

 

Disconnect the power supply. 

2.

 

Remove all connected cables from the measuring unit. 

3.

 

Remove the two screws of the D-Sub connector and the four 
screws on the front panel to remove it. 

4.

 

Remove the two upper screws of the back panel and remove 
the housing cover. 

5.

 

Pull the right board with the D-Sub connector out of the 
connectors of the motherboard. You can also remove the 
entire board from the case. 

6.

 

Locate the switch on the board using the following figure: 

Содержание IPEH-004005-J



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды