PCB Piezotronics Larson Davis EPS044 Скачать руководство пользователя страница 43

Страница: 43 / 57

NMS044 Reference Manual Rev E

LED Indicators

A-3

battery can be shipped in the case, with the correct shipping labels on

the outside of the box.

A.4.1 Lithium Iron Phosphate Battery (LiFePo)

The BAT019 LiFePo is considered Class 9 Hazardous Material, and

additional requirements will need to be met when shipping. A company

and/or individual will need to be 49 CFR and IATA certified to be able to

ship the BAT019 (which is a lithium battery over 100 W Hr). Additionally,

recertification is required every two years.

Licensing can be obtained through a training course, such as the Lion

Technology online training course - code #HMT 254 “Shipping Lithium

Batteries”.

A.5 LED Indicators

A.5.1 SoundAdvisor Model 831C Sound Level Meter

Charge Status LED

The charge status indicated by an LED on

are as follows:

•

LED

continuously lit: Charging

•

LED

not lit: Not charging

•

LED

winking: Charging stopped (battery fault)

•

LED

fast blinking: meter is powering up or shutting down

A.5.2 COM-RV50X-APAC/US:EMEA Cellular Gateway

When installed and running, the state of the RV50X is indicated in the

four LED indicators on the side and bottom of the device. Refer to the

following table for the LED behavior:

Table A.2 Measurement Status LED Indicators

Measurement State

Red LED

Green LED

Stopped with Reset

Winking

***-

Off

Stopped

Blinking

**-*-*

Off

Paused

Flashing

*-*-

Flashing

-*-*

Running

Off

Blinking

**-*-*

Waiting for valid

data to begin

running

Delayed

wink

----*

Off

Содержание Larson Davis EPS044


























































Результаты поиска

Содержание Larson Davis EPS044

Отзывы:

Похожие инструкции для Larson Davis EPS044

Бренды по названию

Популярные бренды

PCB Piezotronics Larson Davis EPS044, Справочное руководство

Результаты поиска

Содержание Larson Davis EPS044

Отзывы:

Похожие инструкции для Larson Davis EPS044

Бренды по названию

Популярные бренды