PCB Piezotronics Larson Davis EPS044 Скачать руководство пользователя страница 16

Страница: 16 / 57

NMS044 Reference Manual Rev E

Configuring for Remote Communication

2-4

Step 2

Using the #0 screwdriver, remove the 2 screws holding the

front SIM card door.

FIGURE 2-3

RV50X Sim Card Slot

Step 3

Insert the SIM card into to the RV50X slot until it clicks.

Step 4

Replace the SIM card door and screws.

Step 5

Remount the RV50X in the case and hand-tighten the 2

case plate screws.

LEARN MORE

To learn more about the RV50X gateway, refer to www.SierraWireless.com.

2.4 Configuring for Remote Communication

In this section:

•

2.4.1 Configuring the Gateway for Remote Comms Using

USB

•

2.4.2 Configuring the Gateway for Remote Comms With a

Mobile Device

This section shows you how to configure the gateway for remote

communication and confirm the service is working properly, first, by

using a USB connection, and second, by using a mobile device.

2.4.1 Configuring the Gateway for Remote Comms Using USB

Before you begin:

• If you’ve purchased the RV50X gateway separately or it has been

reset to factory settings, complete the process shown in

A.7

Configuring LD Settings for the RV50X

• Prepare the battery as shown in

2.2 Preparing the Battery

• Install the SIM card as shown in

2.3.1 Installing the SIM Card

Содержание Larson Davis EPS044


























































Результаты поиска

Содержание Larson Davis EPS044

Отзывы:

Похожие инструкции для Larson Davis EPS044

Бренды по названию

Популярные бренды

PCB Piezotronics Larson Davis EPS044, Справочное руководство

Результаты поиска

Содержание Larson Davis EPS044

Отзывы:

Похожие инструкции для Larson Davis EPS044

Бренды по названию

Популярные бренды