background image

 

PATON 

VDI-SERIES PRO 

 DC MMA/TIG/MIG/MAG  

 

-18- 

3.9. WELDING AT PULSE WELDING CURRENT  

This function is designed to simplify the control of a welding process in various spatial 
welding positions, excluding a flat welding position. This function is also used in welding 
nonferrous  metals.  When  this  function  is  activated,  the  application  of  pulse  welding 
current improves the mixing of molten metals in the weld area and causes forced action 
on the transfer of molten metal drops into the welding pool, therefore the stability of the 
weld formation and the stability of the welding process are improved. The pulse welding 
current  in  the  manual  arc  welding  process  affects  the  weld  parameters  similar  to  the 
movement of the operator hand in manual arc welding process, specifically at hard-to-
reach places.  The proper adjustment of the welding process parameters in the welding at 
pulse welding current has a direct effect on the weld quality, specifically reduces weld 
metal porosity and decreases the graininess of the weld metal. As a result of the improved 
weld quality, the weld strength increases. 
To activate this function, it is necessary to set the following three operational parameters 
of the welding process: current pulse amplitude 

[Po.P]

, current pulse frequency 

[Fr.P]

and  duty  cycle 

[dut].

  By  default,  the  current  pulse  amplitude  is  0 

[OFF],

  that  is,  the 

function is switched off, the current pulse frequency is 50 Hz, and the duty cycle is 50 %. 
To activate the function, set the current pulse amplitude 

[Po.P]

 higher than 0. The current 

pulse  amplitude  should  be  set  in  percentage  of  the  welding  current  specified  for  the 
welding process. 

Example:

 

 

Welding is to be performed with electrode wire 3.0 mm in diameter. 

 

The set welding current is 90 A. 

 

The current pulse amplitude is 40 %. 

 

The current pulse frequency is 50 Hz (default value). 

 

The duty cycle is 50 % (default value). 

The result is the following: the welding current pulse amplitude will be in the range of  
54 … 126 A, the current pulse frequency will be 50 Hz, and the current pulse length will 
be equal to the length of an interval between pulses. If the duty cycle is not equal to  
50 %, the current pulses will be nonsymmetrical relative to the intervals between pulses, 
but the average welding current value will be equal to the set welding current value of 
90 A. As a result, the average heat input to the weld will not change. 
If it is required  to reduce  heat input to the weld, as in  welding thin parts, the  welding 
current should be decreased by performing the standard setting operations. In this case, 
current  pulse  parameters  will  be  adjusted  automatically  according  to  the  set  welding 
current, and the operator can control the reduction of the heat input, as compared with the 
heat  input  at  the  initial  welding  current,  by  simultaneously  varying  the  current  pulse 
amplitude and duty cycle. 
The aforementioned parameters should be set differently for different welding processes, 
depending on the requirements of the operator.  
 

Operations required to set these parameters for the current welding process are described in Section 

6.1

 

Содержание MMA-160P








































Отзывы: