Parkside PVKO 50 B2, Руководство по эксплуатации и технике безопасности

Страница: 25 / 36

20 GB
Noise and vibration
m Warning: Noise can have serious effects on your health. If
the machine noise exceeds 85 dB (A), please wear suitable
hearing protection.
Noise data
The noise levels have been determined in accordance with EN
ISO 3744:1995.
Sound power level L
WA
.............................................. 95.5 dB(A)
Sound pressure level L
pA
............................................ 75.5 dB(A)
Uncertainty K
wa/pA
.........................................................1.9 dB(A)
Vibration parameters
Vibration a
h
.............................................................18.313 m/s²
Uncertainty K
h
................................................................ 1.5 m/s²
Wear hearing protection.
- The total vibration emission values specified and the de-
vice emissions values specified have been measured in
accordance with a standardised test procedure and can
be used for comparison of one electric tool with another.
- The total vibration emission values specified and the de-
vice emissions values specified can also be used for an
initial estimation of the load.
A warning:
- The vibration values and noise emission values can vary
from the specified values during the actual use of the elec-
tric tool, depending on the type and the manner in which
the electric tool is used, and in particular the type of work-
piece being processed.
- It is necessary to determine the safety measures for the pro-
tection of the operator based on an assessment of the vibra-
tion load during the actual conditions of use (In doing so, all
parts of the operating cycle must be taken into account such
as times in which the electric tool is switched off or times in
which it is switched on, but is not running under a load).
8. Unpacking
• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the packaging
and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport damage.
In the event of complaints the carrier must be informed im-
mediately. Later claims will not be recognised.
• If possible, keep the packaging until the expiry of the war-
ranty period.
• Familiarise yourself with the product by means of the operat-
ing instructions before using for the first time.
• With accessories as well as wearing parts and replacement
parts use only original parts. Replacement parts can be ob-
tained from your dealer.
• When ordering please provide our article number as well as
type and year of manufacture for your equipment.
m WARNING!
The device and the packaging material are not children‘s toys!
Do not let children play with plastic bags, films or small parts!
There is a danger of choking or suffocating!
9. Before commissioning
• Before connecting the machine, make certain that the data
on the type plate matches with the mains power data.
• Check the device for transport damage. Immediately report
any damage to the transport company that delivered the
compressor.
• The compressor must be installed close to the consumer.
• Long air lines and supply cables (extension cable) should
be avoided.
• Ensure that the intake air is dry and dust-free.
• Do not deploy the compressor in damp or wet areas.
• Operate the compressor only in suitable areas (well venti-
lated, ambient tempe5°C to 40°C). There must be
no dust, acids, vapours, explosive or flammable gases in the
room.
• The compressor is suitable for use in dry rooms. It must not be
used in areas where splashed water is present.
• The compressor may only be used outdoors briefly when the
ambient conditions are dry.
• The compressor must always be kept dry and must not be left
outdoors after work is complete.
10. Assembly and operation
m Attention!
Always make sure the device is fully assembled
before commissioning!
You require the following for assembly:
2 x open-ended spanner, 13 mm (not included in the scope
of delivery)
10.1 Installing the wheels (Fig. 5)
• Feed the wheel bolt (12) through the hole in the wheel (4).
• Screw the nut (B) onto the wheel bolt (12). Make sure that
the wheel (4) can still be turned on the screw.
• Feed the wheel bolt (12) through the hole in the wheel link-
age.
• Fasten the wheel (4) with the flange nut (D). If necessary,
use an open-ended spanner (not included in the scope of
delivery).
• Repeat the steps with the other tyre (4).
10.2 Installing the foot (Fig. 4)
• Fit the enclosed feet (6) with the 2 hexagonal bolts (A), 2
washers (C) and 2 flange nuts (D) as shown in Fig. 4.
10.3 Mains power connection
• The compressor is equipped with a mains cable with an
earthed plug. This can be connected to any mains socket
230 V~ / 50 Hz with an earth contact and that is protected
at 16 A.
• Before commissioning, ensure that the mains voltage match-
es with the operating voltage and the machine‘s power rat-
ing on the type plate.
• Long supply lines, as well as extensions, cable drums etc.
cause voltage drop and can prevent the motor from starting.
• In the case of temperatures below +5°C, motor starting can
be endangered by sluggishness.