76
GB
-
Use a compressed air device with a low pressure of max.
2 bar.
-
Do not use the compressed air device for the laser.
1. Always keep enough distance to the product.
2. Remove dirt with a compressed air device (max. 2 bar).
13.3 Cleaning the chip extraction system
A chip extraction system is not included in the scope of delivery.
Follow the manufacturer’s operating instructions to properly
clean the extraction system.
14. Transport (fig. 27)
m
WARNING
Danger of injury due to unexpected start-up of the machine
-
Pull the mains plug out of the outlet.
14.1 General notes
• Hold the product at the gripping surfaces.
• Package the product to prevent transport damage. Use the
original packaging.
• Protect the product from vibrations and shocks, in particular
during vehicular transport.
• Ensure adequate load securing when transporting in a ve-
hicle.
14.2 Product-specific notes
m
WARNING
Danger of injury due to excessive product weight.
-
Ask a second person to help you mounting the product.
1. When lifting the product, note its weight see technical data.
2. Always switch off the power tool before transport and dis-
connect it from the power supply.
3. Always carry the power tool with at least one other person,
do not carry by the table extensions. To transport the power
tool, lift it by the machine housing.
4. Protect the power tool from impacts, shocks and severe vibra-
tions, e.g. during vehicular transport.
5. Secure the power tool against toppling and slipping.
6. Never use protective devices for handling or transport.
15. Maintenance
m
WARNING
Danger of injury due to unexpected start-up of the machine
-
Pull the mains plug out of the outlet.
m
WARNING
Warning against unexpected hazards and damages to the
product
-
Never carry out unauthorized changes or repairs to the
product that are not described in the operating manual.
-
Do not carry out work on the product described for a
specialist workshop.
15.1 General notes
• Check the product for loose, worn or damaged components.
• Check the nuts, pins and screws for firm seating.
• Check the covers and protective equipment for damage and
correct seating.
• Check the electrical connections. Repairs to the electrical
connections may only be carried out by a specialist work-
shop.
15.2 Oiling the product
1. Oil the rotating parts once monthly to extend the life of
the tool.
2. Do not oil the motor.
15.3 Servicing carbon brushes
ATTENTION
Product damage
-
The carbon brushes must only be replaced by an electri-
cian.
If excessive sparks are generated, have an electrician check
the carbon brushes.
15.4 Replacing the saw blade
m
WARNING
Danger of injury! Improper handling of the circular table saw
may result in serious injury.
m
WARNING
Danger of injury due to unexpected start-up of the machine
-
Pull the mains plug out of the outlet.
m
WARNING
Danger of injury for fingers and hands due to sharp edges
-
Wear protective gloves.
15.4.1 Removing the saw blade guard (fig. 9)
1. Turn the saw blade (6) to the maximum position out of the
saw table (2) by turning the crank wheel (14) counter-
clockwise until it reaches the stop.
2. Loosen the wing nut (4a).
3. Pull the saw blade guard (4) lightly apart.
4. Carefully slide the saw blade guard (4) over the laser (24)
on the riving knife (5).
15.4.2 Removing the table inlay (fig. 6)
1. Remove the countersunk head screw (7a).
2. Pull the table inlay (7) lightly apart.
3. Carefully slide the table inlay (7) over the laser (24) on the
riving knife (5).
4. Check the table inlay (7) for damage. Replace the table
inlay if it is damaged or no longer connects flush with the
saw table.
15.4.3 Removing the saw blade guard (fig. 28, 29)
PREREQUISITE:
The saw blade (6) has been set to the maxi-
mum cutting depth (see 11.2).
1. Place the open-ended spanner 22 mm (6a) on the outer
saw blade flange (6d) and secure the drive shaft (6e) in
this way.
2. Turn the fixing nut (6f) counterclockwise with the open-end-
ed spanner 22 mm (6b) to undo the fixing nut (6f).
3. Hold the saw blade (6) carefully with one hand and re-
move the fixing nut (6f) and outer saw blade flange (6d)
from the drive shaft (6e).
4. Now remove the saw blade (6) from the drive shaft (6e)
and carefully draw it up and out of the saw table (2).
Содержание PTKS 2000 F4
Страница 87: ......
