53
GB
1. Introduction
Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We hope your new tool brings you much enjoyment and suc-
cess.
Note:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling
• Non-compliance of the operating instructions
• Repairs by third parties, by not authorized service techni-
cians
• Installation and replacement of non-original spare parts
• Application other than specified
• A breakdown of the electrical system that occurs due to the
non-compliance of the electric regulations and VDE regula-
tions 0100, DIN 57113 / VDE0113
Please observe the following:
Read through the complete text in the operating instructions be-
fore installing and commissioning the device.
The operating instructions are intended to help the user to be-
come familiar with the machine and take advantage of its ap-
plication possibilities in accordance with the recommendations.
The operating instructions contain important information on
how to operate the machine safely, professionally and econom-
ically, how to avoid danger, costly repairs, reduce downtimes
and how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt and
moisture. Read the instruction manual each time before operat-
ing the machine and carefully follow its information.
The machine can only be operated by persons who were in-
structed concerning the operation of the machine and who are
informed about the associated dangers. The minimum age re-
quirement must be complied with.
In addition to the safety instructions contained in this operating
manual and the specific regulations of your country, the techni-
cal rules generally accepted for the operation of machines of
the same type must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety in-
formation.
2. Device description (fig. 1-18, 24)
1. Saw table
2. Transverse stop
3. Riving knife
4. Saw blade guard
4a. Screw (saw blade guard)
5. Saw blade
6. Table inlay
7. Parallel stop, complete
8. Hand wheel
9. Locking handle
10. Overload switch
11. On/off switch
12. Rubber foot
13. Tool hook
14. Push stick
15. Locking knob
15a. Clamping plate
16. Holder
16a. Screw (parallel stop)
17. Stop rail
18. Knurled screw (transverse stop)
19. Turning handle
20. Ring spanner, 7/8 mm
21. Ring spanner, 19/10 mm
22. Table width extension
23. Guide tube
24. End piece
25. Screw (end piece)
26. Knurled screw (table width extension)
27. Guide bushing
28. Height adjustment screw
29. Lock nut
30. Support foot
31. Hole (riving knife)
32. Screw (table inlay)
33. Fixing screw (riving knife)
34. Screw (saw blade cover)
35. Saw blade cover
36. Suction port
37. Groove (stop rail)
38. Scale
39. Groove (stop rail)
40. Groove (saw table)
41. Mains cable
42. Bracket for workbench mounting
43. Screw (self-tapping)
44. Washers
Содержание 322850 1901
