Parker Torqmotor TF Series Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 44

background image

HY13-1527-M1/US

Torqmotor™ Service Procedure

TF, TG, TH and TL Series

Parker Hannifin Corporation

Hydraulic Pump/Motor Division

Greeneville, TN 37745 US

28

NOTE

NOTE: Bearing mandrel must be pressed
against the lettered end of bearing shell.
Take care that the housing bore is square
with the press base and the bearing is
not cocked when pressing a bearing into
the housing.

CAUTION

CAUTION: If the bearing mandrel
specified in the “Tools and Materials
Required for Servicing” section is not
available and alternate methods are
used to press in bearing (13) and (19)
the bearing depths specified must be
achieved to insure adequate bearing
support and correct relationship to
adjacent components when assembled.

CAUTION

CAUTION: Because the bearing (13) and
(19) have a press fit into the housing they
must be discarded when removed. They
must not be reused.

Torqmotor™ Assembly

Press in dirt &
water seal

3. Press a

new

dirt and water seal (20) into the

housing (18) outer bearing counterbore.

The dirt and water seal (20) must be
pressed in with the lip facing out and until
the seal is flush to .020 inches (.51 mm)
below the end of housing. SEE FIGURE 30.

Figure 30

«
...
26
27
28
29
30
...
»

Содержание Torqmotor TF Series













































Отзывы:

Нет отзывов

Похожие инструкции для Torqmotor TF Series

Vanguard 540000 Series

Бренд: Briggs & Stratton Страницы: 32

ALCYO ACCU-TRK-AT

Бренд: Oben Страницы: 28

Бренд: Transtecno Страницы: 10

Бренд: Sanshin Страницы: 25

marine TM.5.8TS

Бренд: Toyama Страницы: 88

Бренд: Tanaka Страницы: 7

Бренд: Hatz Страницы: 94

Бренд: STG-BEIKIRCH Страницы: 9

Бренд: RADEMACHER Страницы: 72

Бренд: YS Страницы: 4

Бренд: GPOWER Страницы: 4

Бренд: Yanmar Страницы: 275

Бренд: Parker Hydraulics Страницы: 32

Бренд: O.S. engine Страницы: 4

O.S. Max-160FXRing

Бренд: O.S. engine Страницы: 10

Бренд: Ingersoll-Rand Страницы: 8

Бренд: DLE Страницы: 4

Бренд: Mitsubishi Страницы: 147

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды