Parker Torqmotor TF Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 44

background image

HY13-1527-M1/US

Torqmotor™ Service Procedure

TF, TG, TH and TL Series

Parker Hannifin Corporation

Hydraulic Pump/Motor Division

Greeneville, TN 37745 US

30

Assemble backup
washer & seal

6. A housing (18) that did not require

replacement of the bearing package will
require that the two “captured” thrust
washers (14) and thrust bearing (15) be
unseated and vertical to the counterbore
and the

new

backup ring (17),

new

backup

washer (25), and

new

seal (16) be worked

around the thrust bearing package and
placed into their respective counterbores.
The seal lip must face out of the seal
counterbore and toward the inside of
Torqmotor™ (see figure 60). Be sure the
thrust bearing package is reseated correctly
after assembly of the seal and backup
washer. SEE FIGURES 35 & 36.

CAUTION

CAUTION: Original design TF & TG
Torqmotors™ that do not have backup
washer (25) when disassembled must be
assembled with a new backup ring (17),
new backup washer (25), and new seal
(16).

Apply masking
tape to shaft

7. Apply masking tape around splines or

keyway on shaft (12) to prevent damage to
seal. SEE FIGURE 37.

Figure 37

Figure 36

Figure 35

Torqmotor™ Assembly

«
...
28
29
30
31
32
...
»

Содержание Torqmotor TF Series













































Отзывы:

Нет отзывов

Похожие инструкции для Torqmotor TF Series

Бренд: O.S. engine Страницы: 5

MAX-15CV-R Series

Бренд: O.S. engine Страницы: 19

Бренд: B&S Страницы: 26

Бренд: Indmar Страницы: 80

Бренд: ACDC Страницы: 20

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 110

Бренд: Yamaha Страницы: 110

Бренд: Yamaha Страницы: 232

Бренд: Yamaha Страницы: 305

Бренд: Yamaha Страницы: 307

Бренд: Yamaha Страницы: 372

Бренд: Yamaha Страницы: 444

Бренд: ZF Страницы: 80

Бренд: BMW Страницы: 41

Бренд: Volvo Penta Страницы: 94

MotorLift RA20F

Бренд: Chamberlain Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды