Parker Torqmotor TF Series Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 44

background image

HY13-1527-M1/US

Torqmotor™ Service Procedure

TF, TG, TH and TL Series

Parker Hannifin Corporation

Hydraulic Pump/Motor Division

Greeneville, TN 37745 US

37

One Piece Stator Construction

A disassembled rotor (8A) stator (8B) and vanes (8C) that cannot be readily assembled by hand can be assem-
bled by the following procedures.

Assemble stator

1. Place stator (8B) onto wear plate (9) with

seal ring (4) side down, after following
Torqmotor™ assembly procedures 1
through 13. Be sure the seal ring is in place.
SEE FIGURE 62.

Insert two bolts

2. If assembly alignment studs are not being

utilized, align stator bolt holes with wear
plate and housing bolt holes and turn
two bolts (1) finger tight into bolt holes
approximately 180 degrees apart to retain
stator and wear plate stationary.

Assemble rotor

3. Assemble the rotor (8A), counterbore down

if applicable, into stator (8B), and onto wear
plate (9) with rotor splines into mesh with
drive link (10) splines. SEE FIGURE 63.

NOTE

NOTE: If the manifold side of the
rotor was etched during Torqmotor
disassembly, this side should be up. If
the rotor is not etched and does not have
a counterbore, use the drive link spline
contact pattern apparent on the rotor
splines to determine the rotor side that
must be against the wear plate.

Assemble vanes

CAUTION

Assemble full
complement of
vanes

Remove two
assembled bolts

4. Assemble six vanes (8C), or as many vanes

that will readily assemble into the stator
vane pockets. SEE FIGURE 64.

CAUTION: Excessive force used to push
the rotor vanes into place could shear
off the coating applied to the stator vane
pockets.

5. Grasp the output end of coupling shaft

(12) with locking pliers or other appropriate
turning device and rotate coupling shaft,
drive link and rotor to seat the rotor and
the assembled vanes (8C) into stator
(8B), creating the necessary clearance to
assemble the seventh or full complement
of seven vanes. Assemble the seven vanes
using minimum force. SEE FIGURE 65.

6. Remove the two assembled bolts (1) if used

to retain stator and wear plate.

Go to Torqmotor™ assembly procedure
#15, to continue Torqmotor™ assembly.

Figure 65

Figure 64

Figure 63

Figure 62

Rotor Set Component Assembly

«
...
35
36
37
38
39
...
»

Содержание Torqmotor TF Series













































Отзывы:

Нет отзывов

Похожие инструкции для Torqmotor TF Series

Бренд: Rato Страницы: 65

Бренд: Ofna Racing Страницы: 2

7 HP 212 CC OHV

Бренд: Power Fist Страницы: 52

Бренд: Shindaiwa Страницы: 48

Бренд: GMC Страницы: 7

Бренд: Texas Equipment Страницы: 38

Бренд: YS Страницы: 2

Бренд: Detroit Diesel Страницы: 6

Бренд: Honda Страницы: 96

Бренд: Honda Страницы: 114

Car Engine GX340

Бренд: Honda Страницы: 96

Бренд: Wacker Neuson Страницы: 136

ZA top SM250.60B

Бренд: ZIEHL-ABEGG Страницы: 72

Бренд: 3W Страницы: 17

Бренд: Garmin Страницы: 34

Бренд: Rat Rig Страницы: 14

Бренд: Hatz Diesel Страницы: 129

BLM230- B Series

Бренд: Orientalmotor Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды