Pangolin PASS Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 26

Pangolin PASS Скачать руководство пользователя страница 8

Last update: 2021/04/27 20:10

safety:pass

https://wiki.pangolin.com/doku.php?id=safety:pass

https://wiki.pangolin.com/

Printed on 2022/07/28 09:15

PASS may be controlled by, and may illuminate LEDs on an external control panel that is connected to
PASS. Below is a description of the control panel connections. When PASS is not connected to an external
control panel, then PASS will automatically reset into a “ready” state shortly after power up. When PASS
is connected to an external control panel, then PASS will not power up in a “ready” state and instead, will
wait for the “Manual Reset” from the control panel.

Note that some jurisdictions including the U.S.A. require a manual reset in order to activate the projector
after power up. The PASS control panel connector may be used to help facilitate this feature.

Also note that the signals presented to this connector are generally connected directly to PASS logic
circuits. The signals are not protected from ESD or other electrical faults. For that reason, it is
recommended that any external signals that are connected to this connector be short (i.e. don’t connect
a 30 meter long cable from the external box to the PASS board…)

Pin 1 is the active input that corresponds to an external Emergency Stop (ESTOP) switch, such as a
pushbutton or red “mushroom” type switch. When this pin is connected to Pin 2 (ground), ESTOP is
activated. When Pin 1 is left ﬂoating, then ESTOP is inactive and the projector will be allowed to
operate normally.
Pin 3 is the active input that corresponds to a Manual Reset. This may be connected to pin 4
(ground) through a momentary pushbutton switch or a key-switch.
Pin 5 is an active input that indicates that a control panel is being used. Pin 5 must be connected
to Pin 6 when a control panel is used. If Pin 5 is not connected to Pin 6, then PASS will not wait for a
manual reset when power is ﬁrst applied.
Pins 7 and 8 p5V to the control panel. These may be used in conjunction with LEDs on the
control panel.
Pins 9 and 10 correspond to Ground. These may also be used in conjunction with LEDs on the
control panel.
Pin 11 is an output, which corresponds to the horizon detector within PASS. If this signal is LOW, it
indicates that the Y position is below the horizon (within the audience area). If this signal is HIGH
(approximately 4 volts), it indicates that the Y position is above the horizon. This signal may be
routed through a resistor to an LED or pair of LEDs (bi-color pair) to give an indication on the
control panel as to where the beam is within the Y space.
Pin 13 is an output, which corresponds to the velocity detector within PASS. If this signal is LOW, it

«
...
6
7
8
9
10
...
»

Содержание PASS



























Отзывы:

Нет отзывов