PanelClaw clawFRplus 10 Degree Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 25

PanelClaw clawFRplus 10 Degree Скачать руководство пользователя страница 24

Appendix E (Continued)

Part Number: 5000619

5/16”

flange nut

MLPE

bracket

5/16” bolt

MLPE

5/16”

flange nut

MLPE

bracket

5/16”

bolt

MLPE

5/16”

flange nut

MLPE bracket

5/16”

bolt

ALERT

:

MLPE must be a minimum of 3” away from

the roof, and at least 1.5” from the back sheet of

the module.

MLPE

Solar Edge Installation

Enphase Installation

Tigo Energy Installation

Solar Edge Allowed Installation Locations:

A

Enphase Allowed Installation Locations:

B, C

Tigo Allowed Installation Locations:

A, B, C

ALERT:

Must be Flush

Yotta Energy Installation

3”

3”

Yotta’s

Dual Power Inverter and SolarLeaf are positioned and

installed in the same location as Ballast in the clawFRplus System.
The Rails are to be installed at the location closer to the Cam
Bracket or the portrait ballast installation position. All fasteners
used to install the Dual Power Inverter or SolarLeaf, including any
fasteners removed for installation should be torqued to

6ft-lb.

Alert

: When SolarLeafs are installed, they become a critical

component of the Main Wind Force Resisting System. If SolarLeafs
are removed, quantity 2 4

”x

8

”x

16

”

Nominal 32.6 lbs Ballast Blocks

must be placed in these locations.

Alert

: SolarLeaf

is to be positioned so it is outside of the 3” module

centerline keep out zone.

Alert

: See

Yotta’s

Installation manuals for full installation

instructions on both the Dual Power inverter and SolarLeaf

Keep Out

Zone

«
...
22
23
24
25
»

Содержание clawFRplus 10 Degree


























Отзывы:

Нет отзывов