Panduit ATLONA AT-UHD-PRO3-1616M Скачать руководство пользователя страница 50

Страница: 50 / 76

AT-UHD-PRO3-1616M

Advanced Operation

In control mode, RS-232 commands are sent from a computer or control system (DTE) to the AT-UHD-PRO3-1616M

(DCE). This method allows direct control of the matrix for routing, IP configuration, powering-on / powering-off and

other functions.

Control mode

RS-232

CO
M

+12V SIG

COM

PON

ENT

HDM

SER

IAL

IR OU

SER

IAL

DIGIT

COAX

OUT

AUDI

O OU

AUD

IO I

ETH

ERNE

VID

OUT

48V DC

FACTORY

RESET

AT-UHD-PRO3-1616M

Control System

AT-UHD-PRO3-1616M

FCN

CANCEL

EDID

INFO

POWER

ENTER





Connect the RS-232 cable between the control system and the AT-UHD-PRO3-1616M. Refer to

Cable Assembly

(page 47)

for instructions on preparing the cable.

2. Set the baud rate of the computer/control system to 115200. If the control system is not set to this baud rate,

then the AT-UHD-PRO3-1616M will not respond to RS-232 commands.

3. Refer to the

Applications Programming Interface

for a listing of available commands.

NOTE:

The

RS-232

port on the AT-UHD-PRO3-1616M runs at a default baud rate of 115200.

The control unit must be set to the same baud rate, in order to communicate with the AT-UHD-PRO3-

1616M.

Содержание ATLONA AT-UHD-PRO3-1616M













































































Результаты поиска

Содержание ATLONA AT-UHD-PRO3-1616M

Отзывы:

Panduit ATLONA AT-UHD-PRO3-1616M, Руководство пользователя, Страница: 50 / 76

Результаты поиска

Содержание ATLONA AT-UHD-PRO3-1616M

Отзывы: