Panduit ATLONA AT-HDR-CAT-2 Скачать руководство пользователя страница 20

Страница: 20 / 54

AT-HDR-CAT-2

Device Operation

Selecting EDID

Presets

The AT-HDR-CAT-2 comes with a default EDID plus 8 pre-programmed EDID selections. When selecting the default

or one of the pre-programmed EDID selections, the EDID mode must be set to

INT

(internal) mode.

Available EDID selections are presented in the table below. All resolutions are 60 Hz.

EDID

Description

Connected Display

Uses the downstream EDID of the connected display

ATL 4K60 MCH

3840 x 2160 (UHD) with multichannel audio support

ATL 4K60 PCM MCH

3840 x 2160 (UHD) with PCM multichannel audio support

ATL 1080P MCH

1920 x 1080p with multichannel audio support

ATL 1080P 2CH

1920 x 1080p with two-channel audio support

ATL 1080P DD

1920 x 1080p with Dolby

™

Digital audio support

ATL 1080P DVI

1920 x 1080p for DVI displays

ATL 720P DD

1280 x 720p with Dolby

™

Digital audio support

ATL 720P 2CH

1280 x 720p with two-channel audio support

1. Log in to the web server.

2. Click

EDID

in the menu bar.

3. Make sure the

EDID lock

toggle switch is set to

UNLOCK

4. Click the

EDID mode

drop-down list and select

INT

5. Select the desired EDID from the

INT EDID settings

drop-down list. The selected EDID will be used by the

source, before sending A/V data to the display (sink) device.

NOTE:

If the resolution and timing limitations of both displays, connected to the

HDBaseT OUT

port, are unknown, then select the

Connected Display

EDID for the best compatibility.

The

Connected Display

EDID will automatically build an EDID based on the capabilities of both

displays. When selecting an EDID, make sure both connected displays can support the resolution

and timing information. Otherwise, loss of picture and/or audio may result.

Содержание ATLONA AT-HDR-CAT-2























































Результаты поиска

Содержание ATLONA AT-HDR-CAT-2

Отзывы:

Похожие инструкции для ATLONA AT-HDR-CAT-2

Бренды по названию

Популярные бренды

Panduit ATLONA AT-HDR-CAT-2, Руководство пользователя

Результаты поиска

Содержание ATLONA AT-HDR-CAT-2

Отзывы:

Похожие инструкции для ATLONA AT-HDR-CAT-2

Бренды по названию

Популярные бренды