background image

3

Installation Guide

AT-DISP-CTRL

The AT-DISP-CTRL provides both an 

RS-232

 and 

IR

 port, which can be used to send turn-on/

turn-off commands to the display, when a source is connected to the AT-DISP-CTRL.  Command 

configuration is handled through the web GUI.  Refer to the User Manual for more information.

It is not necessary to connect both RS-232 and IR emitters to control the display.  Either option 

can be used, depending upon the environment and the system setup.

NOTE:

 Typical DB9 connectors use pin 2 for TX, pin 3 for RX, and pin 5 for 

ground. On some devices functions of pins 2 and 3 are reversed.

RS-232 / IR Connector 

RS-232 

IR

1.  Use wire strippers to remove a portion of the cable jacket.
2.  Remove at least 3/16” (5 mm) from the insulation of the RX, TX, and GND wires.
3.  Insert the TX, RX, and GND wires from the DE-9 connector, into the correct terminal using 

the included 4-pin captive screw connector.

1.  Use wire strippers to remove a portion of the cable jacket.
2.  Remove at least 3/16” (5 mm) from the insulation of the GND and Signal (S) wires.
3.  Insert the GND and Signal (S) wires from the IR emitter into the correct terminal using the 

included 4-pin captive screw connector.

HDMI IN

HDMI OUT

SOURCE

POWER

AT-DISP-CTRL

AT-DISP-CTRL

LAN

RX

PoE

TX

TX

RESET

IP MODE

RS-232 IR OUT

DC 5V

FW

GND

DE-9 (RS-232) port

IR Emitter

RX

TX

S

GND

Содержание Atlona AT-DISP-CTRL













Отзывы: