Pandrive PD42-1270 TMCL Скачать руководство пользователя страница 4

Страница: 4 / 87

PD42-1270 TMCL

™

Firmware Manual • Firmware Version V1.00 | Document Revision V1.0 • 2017-Mar-02

4 / 91

Features

The PD42-1270 is a single axis controller/driver PANdrive™ for 2-phase bipolar stepper motors with state

of the art feature set. It is highly integrated, offers a convenient handling and can be used in many

decentralized applications. The PANdrive™ has been designed for coil currents up to 1A RMS and 24V

DC supply voltage. Three digital inputs can be conﬁgured as home and endstop switches or incremental

encoder inputs. With its high energy eﬃciency from TRINAMIC’s coolStep™ technology cost for power

consumption is kept down. The TMCL ﬁrmware allows for both standalone and direct mode operation.

Main characteristics

• Motion controller & stepper motor driver:

–

Hardware motion proﬁle calculation in real-time

–

On the ﬂy alteration of motion parameters (e.g. position, velocity, acceleration)

–

High performance microcontroller for overall system control and communication protocol

handling

–

Up to 256 microsteps per full step

–

High-eﬃcient operation, low power dissipation

–

Dynamic current control

–

Integrated protection

–

stallGuard2™ feature for stall detection

–

coolStep™ feature for reduced power consumption and heat dissipation

–

stealthChop™ feature for quiet operation and smooth motion

–

dcStep™ feature for load dependent speed control

• Interfaces

–

CAN

–

Low-active enable pin

–

Three I/O modes:

* Incremental Encoder and Home Switch

* Home and Endstop Switches

* One analog and two digital inputs

Software

TMCL: remote controlled operation alone or during step/direction mode. PC-based application develop-

ment software TMCL-IDE available for free.

Electrical data

• Supply voltage: +6V and +24V nominal.

• Motor current: up to 1A RMS / 1.41A peak (programmable).

Please see also the separate Hardware Manual.

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Read entire documentation.

Содержание PD42-1270 TMCL
























































































Результаты поиска

Содержание PD42-1270 TMCL

Отзывы:

Похожие инструкции для PD42-1270 TMCL

Бренды по названию

Популярные бренды

Pandrive PD42-1270 TMCL, Руководство пользователя для прошивки

Результаты поиска

Содержание PD42-1270 TMCL

Отзывы:

Похожие инструкции для PD42-1270 TMCL

Бренды по названию

Популярные бренды