Pandrive PD42-1270 TMCL Скачать руководство пользователя страница 23

Страница: 23 / 87

PD42-1270 TMCL

™

Firmware Manual • Firmware Version V1.00 | Document Revision V1.0 • 2017-Mar-02

23 / 91

3.6.7

STGP (Store Global Parameter)

This command is used to store TMCL global parameters permanently in the EEPROM of the module. This

command is mainly needed to store the TMCL user variables (located in bank 2) in the EEPROM of the

module, as most other global parameters (located in bank 0) are stored automatically when being modiﬁed.

The contents of the user variables can either be automatically or manually restored at power on.

Info

For a table with parameters and values which can be used together with this

command please refer to dection

5.2

Internal function:

The global parameter speciﬁed by the type and bank number will be stored in the

EEPROM.

Related commands:

SGP, AGP, GGP, RSGP.

Mnemonic:

STGP <parameter number>, <bank>

Binary Representation

Instruction

Type

Motor/Bank

Value

see chapter

5.2

0 (don’t care)

Reply in Direct Mode

Status

Value

100 - OK

0 (don’t care)

Example

Store user variable #42.

Mnemonic:

STGP 42, 2.

Binary Form of STGP 42, 2

Field

Value

Target address

Instruction number

Type

Motor/Bank

Value (Byte 3)

Value (Byte 2)

Value (Byte 1)

Value (Byte 0)

Checksum

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Read entire documentation.

Содержание PD42-1270 TMCL
























































































Результаты поиска

Содержание PD42-1270 TMCL

Отзывы:

Похожие инструкции для PD42-1270 TMCL

Бренды по названию

Популярные бренды

Pandrive PD42-1270 TMCL, Руководство пользователя для прошивки

Результаты поиска

Содержание PD42-1270 TMCL

Отзывы:

Похожие инструкции для PD42-1270 TMCL

Бренды по названию

Популярные бренды