Pandrive PD42-1270 TMCL Скачать руководство пользователя страница 18

Страница: 18 / 87

PD42-1270 TMCL

™

Firmware Manual • Firmware Version V1.00 | Document Revision V1.0 • 2017-Mar-02

18 / 91

3.6.2

GAP (Get Axis Parameter)

Most motion / driver related parameters of the PD42-1270 can be adjusted using e.g. the SAP command.

With the GAP parameter they can be read out. In standalone mode the requested value is also transferred

to the accumulator register for further processing purposes (such as conditional jumps). In direct mode

the value read is only output in the value ﬁeld of the reply, without affecting the accumulator.

Info

For a table with parameters and values that can be used together with this

command please refer to section

Internal function:

The speciﬁed value gets copied to the accumulator.

Related commands:

SAP, AAP.

Mnemonic:

GAP <parameter number>, <axis>

Binary Representation

Instruction

Type

Motor/Bank

Value

see chapter

<value>

Reply in Direct Mode

Status

Value

100 - OK

value read by this command

Example

Get the actual position of motor 0.

Mnemonic:

GAP 1, 0.

Binary Form of GAP 1, 0

Field

Value

Target address

Instruction number

Type

Motor/Bank

Value (Byte 3)

Value (Byte 2)

Value (Byte 1)

Value (Byte 0)

Checksum

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Read entire documentation.

Содержание PD42-1270 TMCL
























































































Результаты поиска

Содержание PD42-1270 TMCL

Отзывы:

Похожие инструкции для PD42-1270 TMCL

Бренды по названию

Популярные бренды

Pandrive PD42-1270 TMCL, Руководство пользователя для прошивки

Результаты поиска

Содержание PD42-1270 TMCL

Отзывы:

Похожие инструкции для PD42-1270 TMCL

Бренды по названию

Популярные бренды