Panasonic WJ-CU550A, Руководство по эксплуатации

Страница: 83 / 138

-79-
14. Set Up Alarm Mode 3
This table can be set up only after the alarm mode is set to the Off mode in the Alarm Mode Select table.
There is a total of 110 programmable alarm functions available through 10 pages of tables.
1. Move the cursor to the 4 position by moving the Joystick Controller, then press the Set (SET) Key.
2. Move the cursor to the 5 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select the desired Auto Reset (RST) time by moving the Joystick
Controller, then press the Set (SET) Key to execute the selection.
Selected Time in the Window: 30, 60, 90, 120, 150, 180, Off
In this position, press the Increment
(INC) Switch or Decrement (DEC) Switch repeatedly to select the Auto Reset (RST) time
from 1 second to 60 seconds with 1 second increments or decrements.
3. Move the cursor to the 6 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select the desired spot or sequence mode to be assigned to the
monitor by moving the Joystick Controller and pressing the Set (SET) Key to execute the setting.
4. Move the cursor to the 7 position by moving the Joystick Controller. Enter the desired alarm number, 1-128, by pressing the
Numeric Keys.
5. Move the cursor to the 8 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select the desired spot or sequence mode by moving the Joystick
Controller.
If a Tour or Group sequence is selected, use the Numeric Keys to select a particular Tour or Group sequence.
Press the Set
(SET) Key to execute the selection.
6. Move the cursor to the 9 position by moving the Joystick Controller. If the spot mode was selected in step 5 enter the desired
camera number, 1-128, by pressing the Numeric Keys.
7. Move the cursor to the 10 position by moving the Joystick Controller. If the spot mode was selected in step 5 enter the desired
preset number, if applicable, by pressing the Numeric Keys.
8. Move the cursor to the 11 position by moving the Joystick Controller. If the spot mode was selected in step 5 enter the desired
dwell time, 1-30, by pressing the Numeric Keys.
9. Move the cursor to the 12 position by moving the Joystick Controller. If the spot mode was selected in step 5 press the
Function (F4) Key to open the Pop Up Window, select AUX On or Off by moving the Joystick Controller and pressing the Set
(SET) Key to execute the selection.
10. Move the cursor to the 13 position by moving the Joystick Controller.
Press the Function (F4) Key to open the Pop Up Window, select either Set or Reset, by moving the Joystick Controller and
pressing the Set (SET) Key to execute the selection.
11. Press the Escape (ESC) Key to escape from the programming mode. The cursor returns to the 4 position.
Note: An "E" (Error) will appear in the table if an attempt is made to assign an incompatible mode to a monitor. For example, if
an attempt is made to assign a Tour sequence to a monitor that is designated as a Spot monitor.
S e t U p
F 1 : N e x t F 2 : P r e F 3 : D E L F 4 : P o p
P R O G . A l a r m
S e t U p M o d e 3
S 0 1 0 1 1 0
P R E D W E L L
U p
0 2 0 2
0 3
. . O n
. . O f f
P a g e P a g e
A u t o 6 0 s e c
M o d e 3
A l a r m
R S T
A L C A M M O D E
S
T 0 1 0 5
1 2
A U X 1
0 4
0 5
0 5
0 5
0 6
0 7
0 8 G 0 1
S
T 0 2
G 0 2
T 0 3
G 0 3
G 0 4
S G G T G G S G G G G G
2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6
E E
E
S . . S p o t
T . . T o u r
G . . G r o u p . . O K
E . . E r r o r
* . . S e t
P a g e 0 1 o f 1 0
0 1
0 3 1 0 0 2
E
T S
1
2
3
4
5
6
5