Panasonic WH-MXF09D3E5 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 116

background image

51

12.5. Force Heater Mode Operation

The backup heater also serves as backup in case of malfunctioning of the monobloc unit.

1. Make sure the OFF/ON remote control LED is OFF (no operation).
2. Press the Force button to start the force heater mode operation.
3. During force heater mode, all other operations are not allowed.
4. Press OFF/ON button to stop the force heater mode operation.

12.6. Monobloc Unit Safety

12.6.1. Monobloc Unit Safety Control

1. When water pump is ON, the system will start checking flow switch status (ON/OFF).
2. If the flow switch ON for 10 seconds, the system will check on the water inlet temperature for 10 seconds.

If the water inlet temperature not exceeds 80

°

C, the water pump shall be continuously running with normal mode.

If the water inlet temperature exceeds 80

°

C for continuously 10 seconds, the water pump will be OFF immediately.

3. After water pump OFF for more than 10 minutes, it will be ON back and the monobloc unit safety control checking is restarted.

12.7. Auto Restart Control

1. When the power supply is cut off during the operation of Monobloc unit, the compressor will re-operate after power supply

resumes.

«
...
49
50
51
52
53
...
»

Содержание WH-MXF09D3E5





















































































































Отзывы:

Нет отзывов

Похожие инструкции для WH-MXF09D3E5

Бренд: EarthLinked Страницы: 6

Бренд: Zibro Страницы: 16

Бренд: Zibro Страницы: 17

Бренд: Panasonic Страницы: 55

Бренд: Xylem Страницы: 92

LOWARA e-SV Series

Бренд: Xylem Страницы: 48

American Pride ACNF Series

Бренд: Amana Страницы: 8

Бренд: Prem-I-Air Страницы: 7

Бренд: Modine Manufacturing Страницы: 32

NEXIS-VE Series

Бренд: salmson Страницы: 120

Бренд: Reality Leuchten Страницы: 86

EASYDOS Peristaltic V

Бренд: Jesco Страницы: 20

Бренд: vacuubrand Страницы: 70

Бренд: L.B. White Страницы: 24

Бренд: Oase Страницы: 7

Бренд: Daikin Страницы: 24

Corken Z-Series

Бренд: Idex Страницы: 32

Бренд: T.I.P. Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды