Panasonic WH-MXF09D3E5 Скачать руководство пользователя страница 67

Страница: 67 / 116

16.4. Error Codes Table

Abnormality / Protection control

Abnormality Judgement

Primary location to verify

Diagnosis display

H00

No abnormality detected

—

H12

Indoor/Outdoor capacity unmatched

90s after power supply

• Indoor/outdoor connection wire
• Indoor/outdoor PCB
• Specification and combination table in

catalogue

H15

Outdoor compressor temperature sensor
abnormality

Continue for 5 sec.

• Compressor temperature sensor

(defective or disconnected)

H23

Indoor refrigerant liquid temperature
sensor abnormality

Continue for 5 sec.

• Refrigerant liquid temperature sensor

(defective or disconnected)

H42

Compressor low pressure abnormality

—

• Outdoor pipe temperature sensor
• Clogged expansion valve or strainer
• Insufficient refrigerant
• Outdoor PCB
• Compressor

H62

Water flow switch abnormality

Continue for 1 min.

• Water flow switch

H64

Refrigerant high pressure abnormality

Continue for 5 sec.

• Outdoor high pressure sensor

(defective or disconnected)

H70

Back-up heater OLP abnormality

Continue for 60 sec.

• Back-up heater OLP

(Disconnection or activated)

H72

Tank sensor abnormal

Continue for 5 sec.

• Tank sensor

H76

Indoor - remote control communication
abnormality

—

• Indoor - control panel

(defective or disconnected)

H90

Indoor / outdoor abnormal
communication

> 1 min after starting operation

• Internal / external cable connections
• Indoor / Outdoor PCB

H91

Tank heater OLP abnormality

Continue for 60 sec.

• Tank heater OLP

(Disconnection or activated)

H95

Indoor/Outdoor wrong connection

—

• Indoor/Outdoor supply voltage

H98

Outdoor high pressure overload
protection

—

• Outdoor high pressure sensor
• Water pump or water leakage
• Clogged expansion valve or strainer
• Excess refrigerant
• Outdoor PCB

H99

Indoor heat exchanger freeze prevention

—

• Indoor heat exchanger
• Refrigerant shortage

F12

Pressure switch activate

4 times occurrence within 20
minutes

• Pressure switch

F14

Outdoor compressor abnormal revolution

4 times occurrence within 20
minutes

• Outdoor compressor

F15

Outdoor fan motor lock abnormality

2 times occurrence within 30
minutes

• Outdoor PCB
• Outdoor fan motor

F16

Total running current protection

3 times occurrence within 20
minutes

• Excess refrigerant
• Outdoor PCB

F20

Outdoor compressor overheating
protection

4 times occurrence within 30
minutes

• Compressor tank temperature sensor
• Clogged expansion valve or strainer
• Insufficient refrigerant
• Outdoor PCB
• Compressor

F22

IPM (power transistor) overheating
protection

3 times occurrence within 30
minutes

• Improper heat exchange
• IPM (Power transistor)

F23

Outdoor Direct Current (DC) peak
detection

7 times occurrence
continuously

• Outdoor PCB
• Compressor

F24

Refrigeration cycle abnormality

2 times occurrence within 20
minutes

• Insufficient refrigerant
• Outdoor PCB
• Compressor low compression

F25

Cooling / Heating cycle changeover
abnormality

4 times occurrence within 30
minutes

• 4-way valve
• V-coil

F27

Pressure switch abnormality

Continue for 1 min.

• Pressure switch

F36

Outdoor air temperature sensor
abnormality

Continue for 5 sec.

• Outdoor air temperature sensor

(defective or disconnected)

F37

Indoor water inlet temperature sensor
abnormality

Continue for 5 sec.

• Water inlet temperature sensor

(defective or disconnected)

F40

Outdoor discharge pipe temperature
sensor abnormality

Continue for 5 sec.

• Outdoor discharge pipe temperature

sensor (defective or disconnected)

Содержание WH-MXF09D3E5





















































































































Результаты поиска

Содержание WH-MXF09D3E5

Отзывы:

Похожие инструкции для WH-MXF09D3E5

Бренды по названию

Популярные бренды

Panasonic WH-MXF09D3E5, Руководство по обслуживанию

Результаты поиска

Содержание WH-MXF09D3E5

Отзывы:

Похожие инструкции для WH-MXF09D3E5

Бренды по названию

Популярные бренды