FA
Q
s
115
Problem
Actions
S
cr
een
Chaotic image, noisy
•
Set [P-NR] in the Picture Menu (to remove noise).
(p. 38)
•
Check nearby electrical products
(fluorescent lamp, DECT phones, mobile phones, microwave, etc.).
No image can be
displayed
•
Is [Contrast], [Brightness] or [Colour] in the Picture Menu set to the minimum?
(p. 38)
•
Please also refer to “Neither image nor sound is produced”
(p. 114)
Blurry or distorted image
(no sound or low volume)
•
Reset channels.
(p. 48, 49)
•
Please also refer to “Neither image nor sound is produced”
(p. 114)
Unusual image is
displayed
•
Turn the TV Off with Mains power On / Off switch, then turn it On again.
•
If the problem persists, initialise all settings
[Shipping Condition] (p. 62)
S
ound
No sound is produced
•
Is Sound Mute active?
(p. 9)
•
Is the volume set to the minimum?
•
Is Speaker Selection (VIERA Link) set to [TV]?
•
Please also refer to “Neither image nor sound is produced”
(p. 114)
Sound level is low or
sound is distorted
•
Sound signal reception may be deteriorated.
•
Set [NICAM] (p. 40) in the Sound Menu to [Off ]. (Analogue only)
•
Please also refer to “Neither image nor sound is produced”
(p. 114)
Unusual sound from
the TV
•
When power is on, whirring sound of cooling fan or drive noise may be heard from
inside the TV (not a sign of faulty operation).
3D
Cannot see 3D images
•
Has the 3D Eyewear been switched On?
•
Ensure that [3D Mode Selection] is set to [3D].
(p. 34)
•
Some 3D image signals may not be automatically recognised as 3D images. Set [3D Mode
Selection (Manual)] to match the picture format.
(p. 34)
•
Check that there are no obstacles between the infrared sensors on the TV and the 3D
Eyewear. If the 3D Eyewear stops receiving the infrared signal for about 5 minutes, the 3D
Eyewear will be turned off automatically.
•
Check the available area to use the 3D Eyewear.
(p. 33)
•
Depending on the person, the 3D images may be difficult to see, or cannot be seen,
especially in users that have a different level of eyesight between the left and right eyes.
Take the necessary steps (wearing glasses etc.) to correct your eyesight before use.
3D Eyewear is turned
off automatically
•
Check that there are no obstacles between the infrared sensors on the TV and the 3D
Eyewear or that the 3D Eyewear is placed inside the coverage area (p. 33). If the 3D
Eyewear stops receiving the infrared signal for about 5 minutes, the 3D Eyewear will be
turned off automatically.
There is something
wrong with the 3D
images
•
Check the setting of [Picture Sequence] or [Edge Smoother].
(p. 33)
The indicator lamp does
not light when pressing
the power button on
the 3D Eyewear
•
The battery may be running low or flat. Replace it.
Digital Channel
No programmes shown
on TV Guide
•
Reset channels.
(p. 48, 49)
•
Check the digital transmission by contacting Digital UK on 08456 50 50 50 or at www.
digitaluk.co.uk
•
Check the analogue broadcast (if still available in your area).
•
Consult an aerial engineer to check the alignment of your aerial.
Cannot find a channel
you have previously
watched
•
The channel may broadcast for part of the day.
•
Check the channel in the TV Guide.
(p. 22)
•
Channel position numbers may be changed by broadcasters.
•
Reset channels.
(p. 48, 49)
HDMI
Sound is unusual
•
Set the sound setting of the connected equipment to “2ch L.PCM”.
•
Check the [HDMI1 / 2 / 3 / 4 Input] setting in the Sound Menu.
(p. 40)
•
If digital sound connection has a problem, select analogue sound connection.
(p. 110)
Pictures from external
equipment are unusual
when the equipment is
connected via HDMI
•
Check the HDMI cable is connected properly.
(p. 103)
•
Turn the TV and equipment Off, then turn them On again.
•
Check an input signal from the equipment.
(p. 112)
•
Check the output resolution of the equipment.
•
Use equipment compliant with EIA/CEA-861/861D.
