38
RQT9129
Messages
The following messages or ser
v
ice numbers appear on the TV or unit’s display when something unusual is detected during startup and use.
On the TV
Page
Cannot play.
≥
You inserted an incompatible disc (Discs recorded in PAL
v
ideo, etc.).
12, 13
Cannot display on this unit.
≥
You tried to play a non-compatible image.
≥
Confirm “SD” on the unit’s display is not blinking and re-insert the card.
13
—
No disc
≥
The disc may be upside down.
—
This disc is incompatible.
≥
You inserted an incompatible disc.
12, 13
$
This operation is currently
disabled.
≥
The operation is prohibited by the unit or disc.
—
On the unit’s display
ERROR
≥
Incorrect operation performed. Read the instructions and try again.
—
F99
≥
The unit fails to operate properly. Press [POWER
Í
/I] on the main unit to switch the unit to
standby for 3 seconds. Now press [POWER
Í
/I] on the main unit again to turn the unit on.
—
HDMI ONLY
≥
Some BD-Video discs can only be output with HDMI.
—
No PLAY
≥
There is a
v
iewing restriction on a BD-Video or DVD-Video.
32
No READ
≥
The disc is dirty or badly scratched. The unit cannot play.
—
PLEASE WAIT
≥
Displayed when the unit is started and turned off. This is not a malfunction.
≥
The unit is carrying out its reco
v
ery process. You cannot operate the unit while “PLEASE
WAIT” is displayed.
—
—
SET
(“
” stands for a number.)
≥
The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [OK] and the indicated number button at the same
time for more than 5 seconds.
42
UNFORMAT
≥
You inserted an unformatted DVD-RAM, DVD-RW, +RW, an R, +R DL or
DVD-RW (DVD-Video format).
—
UNSUPPORT
≥
You ha
v
e inserted a disc the unit cannot play.
12, 13
U59
≥
The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good
v
entilation when installing the unit. Do not block the cooling fan
on the rear of the unit.
—
“
[W2S]
” or “
[W4S]
” is flashing.
≥
There is no link between the main unit and the wireless system. Check that the wireless
system is plugged into the AC outlet and is turned on.
≥
Ensure that the digital transmitter is fully inserted into the slot of the main unit.
≥
Perform the steps bellow.
1
While pressing the [
9
/
5
] on the main unit, press the numbered button [3] on the
remote control until “P” lights in the main unit’s display.
≥
The indicator on the wireless system turns green.
2
While “P” is displayed, press [I/D SET] on the rear of the
wireless system.
≥
If “P” goes off before you press [I/D SET], repeat step
1
and then continue the procedure.
3
While pressing [
9
/
5
] on the main unit, press the
numbered button [3] on the remote control.
≥
“
[W2S]
” or “
[W4S]
” lights on the main unit.
4
Turn off and on the wireless system.
≥
Make sure the indicator on the wireless system lights up green.
8
6
—
U72
U73
≥
The HDMI connection acts unusually.
– The connected equipment is not HDMI compatible.
– Please use HDMI cables that ha
v
e the HDMI logo (as shown on the co
v
er).
– The HDMI cable is damaged.
—
H
or F
≥
Check and correct the speaker cable connections.
≥
There is something unusual. (The ser
v
ice number displayed after H and F depends on the
unit’s condition.)
≥
Check the unit using the troubleshooting guide. If the ser
v
ice number does not disappear,
do the following.
1
Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it.
2
Press [POWER
Í
/I] to turn the power on. (The unit may be fixed.)
If the ser
v
ice number does not disappear despite doing the abo
v
e, request ser
v
ice from
the dealer. Inform the dealer of the ser
v
ice number when requesting ser
v
ice.
6
—
39–42
NOT CONDITIONAL
NO SURROUND SPEAKER
≥
7.1ch Virtual Surround is a
v
ailable only when playing 6ch sources or abo
v
e.
≥
7.1ch Virtual Surround is a
v
ailable only when speaker setting is set to 5.1-channel.
27
27, 33, 34
I/D SET
Use a pointed
object.
SC-BT100P-ENG.book 38 ページ ２００８年２月２０日 水曜日 午後６時２２分
