8
8
1. Press during operation.
• You can toggle between ON and OFF each time you press .
• “ ” is displayed when this setting is ON.
• When the nanoe™ X setting is ON, “nanoe” (atomised water particle)
is released from the indoor unit while in operation (Cool, Dry, Heat,
Fan, Auto).
• If the receiver emits 1 short beep followed by 1 long beep after
pressing , the indoor unit does not support this function.
See the section “8-12. Button Control” on page 8-12 for how to
enable or disable the button.
• “ ” is displayed if the function is not available.
nanoeX
ECONA
V
I
ECONA
V
I
ECONA
V
I
nanoeX
nanoeX
1
(ECONAVI can be set using the separately sold ECONAVI panel or by
connecting the holder on the wall.)
1. Press during operation.
• You can toggle between ON and OFF each time you press .
• “ ” is displayed when this setting is ON. *
• The ECONAVI sensor detects human activity and conserves
energy based on the activity level.
• Even when target temperature is changed through the ECONAVI
function, the set temperature shown in the remote controller does not
change.
• When operating more than 1 indoor unit, the energy-saving effect may
be reduced depending on the room condition.
• If the receiver emits 1 short beep followed by 1 long beep after pressing
, the indoor unit does not support this function.
See the section “8-12. Button Control” on page 8-12 for how to enable
or disable the button.
• “ ” is displayed if the function is not available.
* “ ” is not displayed in Fan mode.
1
8-13. nanoe™ X Setting
8-14. ECONAVI Setting
(When connected to an aftermarket fan)
button is disabled as the factory setting. Enable the button if you
have connected the ventilation fan.
(See the section “8-12. Button Control” on page 8-12.)
1. Press .
• You can toggle between ON and OFF each time you press .
• “ ” appears on the display of the remote controller when the fan is
operating.
• When the air conditioner is started or stopped, the fan starts or stops at
the same time.
• “ ” is displayed if the function is not available.
1. Press during operation.
• You can toggle between ON and OFF each time you press .
• “ ” is displayed when this setting is ON.
• The energy saving operation restricts the maximum current value,
resulting in decreased cooling/heating performance. (If the current of
outdoor units does not reach the peak due to low load operation, the
current value is not restricted.)
• If the receiver emits 1 short beep followed by 1 long beep after
pressing , the indoor unit does not support this function.
See the section “8-12. Button Control” on page 8-12
for how to enable or disable the button.
• “ ” is displayed if the function is not available.
1
1
8-15. Ventilation Setting
8-16. Energy Saving Setting
8-13
SM830277-00_大洋州向け R32シングル_TD&SM.indb 13
19/02/12 10:54:27
Содержание S-160PE1R5B
