Secure the drain hose with a sucker
4
Trial operation
5
●
Make sure that all adhesive tapes used to fix the door and inside of the dishwasher and the
packaging bags of all parts have been removed.
●
Make sure that the supply valve is open, plug in the power plug and close the door.
●
Please perform a trial test of the dishwasher according to the following procedures.
· If there is no water supply and electricity supply temporarily, perform a trial test of the
dishwasher when water supply and electricity supply resume. (Do not fill in water by hand)
Drain hose
→
If the drain hose is too long, cut neatly at the appropriate
position along the core wire (transparent).
sucker
■
Procedures for trial operation
· Please confirm the following during and after the operation.
· Power will automatically be turned off and the display indictors light off after
completion of the trial operation
· The indictors for Speedy and Care in the display light up and emit 2 beep sounds
EN23
❶
Press to turn on the power
❷
Press and hold for more than 3 seconds simultaneously
❸
Press to start the trial operation
●
After the trial operation is completed, keep the supply valve open.
●
If the dishwasher will not be used for a long time, close the water valve to avoid water leakage.
●
If freezing may occur, arrange draining treatment. (It may cause damage to the supply valve
resulting water leakage) → If freezing occurs, contact Service Centre
Reminder
■
Trial operation confirmation
Error indication :
There should be no alarm sound nor abnormal indication on the display.
(page EN16)
Water leakage :
There should be no leakage at the joints of the water supply hose and drain hose.
After 6 beep sounds, power will be automatically turned off
Drainage condition :
Open the door and confirm that the water inside the dishwasher
has been drained out.
No water supply condition :
When the power is off, confirm that no water is draining
out from the drain outlet.
During operation
When the operation completed
Installation Instructions
(cont.)
Checkup
6
●
Please check the following before use.
Is the dishwasher installed on a solid horizontal surface? Make sure it won't shake or tilt.
Is the water supply hose tightened, steady and straight?
Is there no water leakage at the connection between the water supply hose and the back
of the dishwasher?
Is there no water leakage at the connection between the water supply hose and the supply valve?
(If there is water leakage, please check whether the gasket is fitted properly.)
Is the drain hose tightened, steady and straight?
Is the drain hose bent, entangled, or damaged?
Is the drain hose raised 20 cm or more?
(Examples of incorrect drain hose arrangement)
Bent
Entangled
Raised 20 cm
EN24
NP-TH1HK.indd 26
2018/11/29 15:06:20
Job Name
B685891_NP-TH1取説(香港)
Color
K
File Name
0026_NP-TH1HK.pdf
Refine Time
2018-11-29 15:12:59
Print Time
2018-12-10 15:25:02
Job Name
B685891_NP-TH1取説(香港)
Color
K
File Name
0026_NP-TH1HK.pdf
Refine Time
2018-11-29 15:12:59
Print Time
2018-12-10 15:25:02
English
Secure the drain hose with a sucker
4
Trial operation
5
●
Make sure that all adhesive tapes used to fix the door and inside of the dishwasher and the
packaging bags of all parts have been removed.
●
Make sure that the supply valve is open, plug in the power plug and close the door.
●
Please perform a trial test of the dishwasher according to the following procedures.
· If there is no water supply and electricity supply temporarily, perform a trial test of the
dishwasher when water supply and electricity supply resume. (Do not fill in water by hand)
Drain hose
→
If the drain hose is too long, cut neatly at the appropriate
position along the core wire (transparent).
sucker
■
Procedures for trial operation
· Please confirm the following during and after the operation.
· Power will automatically be turned off and the display indictors light off after
completion of the trial operation
· The indictors for Speedy and Care in the display light up and emit 2 beep sounds
EN23
❶
Press to turn on the power
❷
Press and hold for more than 3 seconds simultaneously
❸
Press to start the trial operation
●
After the trial operation is completed, keep the supply valve open.
●
If the dishwasher will not be used for a long time, close the water valve to avoid water leakage.
●
If freezing may occur, arrange draining treatment. (It may cause damage to the supply valve
resulting water leakage) → If freezing occurs, contact Service Centre
Reminder
■
Trial operation confirmation
Error indication :
There should be no alarm sound nor abnormal indication on the display.
(page EN16)
Water leakage :
There should be no leakage at the joints of the water supply hose and drain hose.
After 6 beep sounds, power will be automatically turned off
Drainage condition :
Open the door and confirm that the water inside the dishwasher
has been drained out.
No water supply condition :
When the power is off, confirm that no water is draining
out from the drain outlet.
During operation
When the operation completed
Installation Instructions
(cont.)
Checkup
6
●
Please check the following before use.
Is the dishwasher installed on a solid horizontal surface? Make sure it won't shake or tilt.
Is the water supply hose tightened, steady and straight?
Is there no water leakage at the connection between the water supply hose and the back
of the dishwasher?
Is there no water leakage at the connection between the water supply hose and the supply valve?
(If there is water leakage, please check whether the gasket is fitted properly.)
Is the drain hose tightened, steady and straight?
Is the drain hose bent, entangled, or damaged?
Is the drain hose raised 20 cm or more?
(Examples of incorrect drain hose arrangement)
Bent
Entangled
Raised 20 cm
EN24
NP-TH1HK.indd 27
2018/11/29 15:06:34
Job Name
B685891_NP-TH1取説(香港)
Color
K
File Name
0027_NP-TH1HK.pdf
Refine Time
2018-11-29 15:12:57
Print Time
2018-12-10 15:25:02