Error Indication
(cont.)
EN17
Freezing prevention Not in use for a long time
In the event of freezing occurs and the problem is ignored, it may cause damage to the supply
valve and piping. For draining treatment and freezing prevention, please contact Service Centre.
■
If the relevant parts or pipes were already frozen, please do the following
❶
Select Speedy to run 1 - 2 times to defrost.
(If the situation is serious, repeat the operation several times)
❷
After the process is completed, wait for 30 minutes, remove the supply hose from the
dishwasher, and drain out the water from the hose.
❸
Take off the rubber cover (black) at the front, shake the dishwasher on all sides, and drain out
all the water inside.
❹
Put the rubber cover back in place.
Panasonic staff handling the draining should note the following:
Troubleshooting
■
Check the following first. If the problem still continues or there are other symptoms, please contact Service Centre.
EN18
●
Is the door closed firmly?
→
Close the door firmly and restart the operation.
●
Dew condensation may occur due to the temperature difference between the
dishwasher body and the kitchen, which is not a malfunction.
●
Steam or warm air may come out, but this is not a malfunction.
●
This is caused by the minerals contained in the water.
●
Water may be left at the bottom. This is normal.
●
The water supply valve may be broken. Close the water supply valve or
the water tap valve (but leave the power plug connected), and contact
Service Centre.
●
For a while after it is purchased, the rubber and resin components of the
dishwasher may emit some odour, which have no adverse effect on the
human body and will disappear after a period of time.
●
This is due to residue such as fish skin left on the filter.
→
Remove and clean it using a brush (page EN13). If the smell persists,
select and run the Care program.
●
This is the sound of the nozzles switching sequentially before spraying,
which is not a malfunction.
●
Depending on the types of tableware and how they are loaded, the noises
may get louder during operation.
●
Are the filters clogged? (When the filters are clogged, the sound of the pump
may suddenly become loud during operation.) → Clean the filters (page EN13)
●
During operation, the electronic components will make chattering sounds
when they are switched. This is not a malfunction.
●
Is the dishwasher (location, drain hose, supply hose) installed correctly?
→ Check carefully (page EN24)
●
A foul odour may be generated as a result of the deterioration of water remained in
the appliance if it is left unused for a long time. → Select and run the Care program.
●
Have you used kitchen detergents? Or is kitchen detergent not rinsed off completely
from the items in the pre-wash?
→
You must use dishwasher detergent.
(Kitchen detergent may generate excessive foam. Supplying and draining
water repeatedly is necessary to eliminate the foam. The operation time will
be prolonged. Do not open the door during the process to avoid water leakage.)
Symptoms
Causes and Solutions
The appliance
does not work
Water is supplied and
drained repeatedly
Dew condensation
around the door.
Odour emits during
operation
Fishy smell
Noises change during
operation
Freezing
Water leakage
Water supply stops
Power cut
Circuit breaker has
tripped
"Salt" stays
lighted up in the display
When the nozzles start
spraying, they make a
clattering sound
Smell like a sewer
Steam comes out from
around the door during
operation.
After using for a while,
the inside walls of the
dishwasher become whitish.
Water is left under
the filter
Water supply does not
stop
Dishwasher Body
Smell
●
①
Select and run the Speedy program 1 - 2 times (to defrost).
②
Check whether you can run the Speedy program.
• If the freezing is the result of being left unused for a long period of time,
defrost may not work even after running the Speedy program 1 - 2 times.
→
Contact Service Centre (page EN17)
●
Turn off the power to stop the operation. When water supply resumes,
discharge the muddy water from another tap, and then restart the operation.
●
When electricity supply resumes, press Start/Pause to restart the operation.
• The program will resume from the beginning of the process which was running
at the time of the power cut.
• If delay start was selected and was waiting to start later, the selected program
with delay start will be cancelled.
●
Check the causes, reset the circuit breaker, press Start/Pause to restart the operation.
• The program will resume from the beginning of the process which was running
at the time of the power cut.
• If delay start was selected and was waiting to start later, the selected program with
delay start will be cancelled.
●
For Hong Kong with option code "0", there is no need to add salt. (page EN9)
Abnormal sound
Others
NP-TH1HK.indd 20
2018/11/29 15:02:30
Job Name
B685891_NP-TH1取説(香港)
Color
K
File Name
0020_NP-TH1HK.pdf
Refine Time
2018-11-29 15:12:56
Print Time
2018-12-10 15:25:00
Job Name
B685891_NP-TH1取説(香港)
Color
K
File Name
0020_NP-TH1HK.pdf
Refine Time
2018-11-29 15:12:56
Print Time
2018-12-10 15:25:00
English
Error Indication
(cont.)
EN17
Freezing prevention Not in use for a long time
In the event of freezing occurs and the problem is ignored, it may cause damage to the supply
valve and piping. For draining treatment and freezing prevention, please contact Service Centre.
■
If the relevant parts or pipes were already frozen, please do the following
❶
Select Speedy to run 1 - 2 times to defrost.
(If the situation is serious, repeat the operation several times)
❷
After the process is completed, wait for 30 minutes, remove the supply hose from the
dishwasher, and drain out the water from the hose.
❸
Take off the rubber cover (black) at the front, shake the dishwasher on all sides, and drain out
all the water inside.
❹
Put the rubber cover back in place.
Panasonic staff handling the draining should note the following:
Troubleshooting
■
Check the following first. If the problem still continues or there are other symptoms, please contact Service Centre.
EN18
●
Is the door closed firmly?
→
Close the door firmly and restart the operation.
●
Dew condensation may occur due to the temperature difference between the
dishwasher body and the kitchen, which is not a malfunction.
●
Steam or warm air may come out, but this is not a malfunction.
●
This is caused by the minerals contained in the water.
●
Water may be left at the bottom. This is normal.
●
The water supply valve may be broken. Close the water supply valve or
the water tap valve (but leave the power plug connected), and contact
Service Centre.
●
For a while after it is purchased, the rubber and resin components of the
dishwasher may emit some odour, which have no adverse effect on the
human body and will disappear after a period of time.
●
This is due to residue such as fish skin left on the filter.
→
Remove and clean it using a brush (page EN13). If the smell persists,
select and run the Care program.
●
This is the sound of the nozzles switching sequentially before spraying,
which is not a malfunction.
●
Depending on the types of tableware and how they are loaded, the noises
may get louder during operation.
●
Are the filters clogged? (When the filters are clogged, the sound of the pump
may suddenly become loud during operation.) → Clean the filters (page EN13)
●
During operation, the electronic components will make chattering sounds
when they are switched. This is not a malfunction.
●
Is the dishwasher (location, drain hose, supply hose) installed correctly?
→ Check carefully (page EN24)
●
A foul odour may be generated as a result of the deterioration of water remained in
the appliance if it is left unused for a long time. → Select and run the Care program.
●
Have you used kitchen detergents? Or is kitchen detergent not rinsed off completely
from the items in the pre-wash?
→
You must use dishwasher detergent.
(Kitchen detergent may generate excessive foam. Supplying and draining
water repeatedly is necessary to eliminate the foam. The operation time will
be prolonged. Do not open the door during the process to avoid water leakage.)
Symptoms
Causes and Solutions
The appliance
does not work
Water is supplied and
drained repeatedly
Dew condensation
around the door.
Odour emits during
operation
Fishy smell
Noises change during
operation
Freezing
Water leakage
Water supply stops
Power cut
Circuit breaker has
tripped
"Salt" stays
lighted up in the display
When the nozzles start
spraying, they make a
clattering sound
Smell like a sewer
Steam comes out from
around the door during
operation.
After using for a while,
the inside walls of the
dishwasher become whitish.
Water is left under
the filter
Water supply does not
stop
Dishwasher Body
Smell
●
①
Select and run the Speedy program 1 - 2 times (to defrost).
②
Check whether you can run the Speedy program.
• If the freezing is the result of being left unused for a long period of time,
defrost may not work even after running the Speedy program 1 - 2 times.
→
Contact Service Centre (page EN17)
●
Turn off the power to stop the operation. When water supply resumes,
discharge the muddy water from another tap, and then restart the operation.
●
When electricity supply resumes, press Start/Pause to restart the operation.
• The program will resume from the beginning of the process which was running
at the time of the power cut.
• If delay start was selected and was waiting to start later, the selected program
with delay start will be cancelled.
●
Check the causes, reset the circuit breaker, press Start/Pause to restart the operation.
• The program will resume from the beginning of the process which was running
at the time of the power cut.
• If delay start was selected and was waiting to start later, the selected program with
delay start will be cancelled.
●
For Hong Kong with option code "0", there is no need to add salt. (page EN9)
Abnormal sound
Others
NP-TH1HK.indd 21
2018/11/29 17:28:47
Job Name
B685891_NP-TH1取説(香港)
Color
K
File Name
0021_NP-TH1HK.pdf
Refine Time
2018-11-29 17:30:47
Print Time
2018-12-10 15:25:00
