manualshive.com logo in svg

Panasonic MINAS-A5NL Series, Техническое описание

Поделиться
Скачать
Panasonic MINAS-A5NL Series Скачать руководство пользователя страница 109

No. SX-DSV02310 - 101 - 

R2.0 Motor 

Business 

Division, 

Appliances Company, Panasonic Corporation 

6-10-2 List of command error code 

 

Category 

Error_Code 

Cause 

0011h 

•  Mismatched node address (MAC-ID) 

Command header 
related 

0012h 

•  C/R bit is 1 despite of command 
•  Sub_Chk is 0 in 32-byte mode. 

0021h 

•  Cyclic command is not defined 

0022h 

•  Non-cyclic command is not defined (when cyclic command is normal) 
•  Conbination error of control mode and non-cyclic command. 
•  Subcommand is undefined in 32-byte mode. 

Command code, 
control mode 
related 

002Eh 

•  Combination of communication cycle,16/32-byte mode and control mode is not correct. 
•  Control mode has been changed by less than 2 ms. 
•  Control mode has been changed during profile position latch positioning/profile homing (Type_Code = 

12h, 13h, 31h, 32h, 33h,34h,35h) operation. 

•  Control mode has been changed during execution of non-cyclic command (Busy = 1). 
•  Run the home return command (

4h) Type_Code=1

h/2

h during the velocity control (CV)/ thrust 

control (CT) 

• When Block Diagram of 2 Degrees of Freedom Mode is disabled, Control mode has been changed other 

than position control. 

0031h • 

Type_Code/Sub_Type_Code is not defined. 

0032h 

•  Non-cyclic data/subcommand data other than Type_Code/Sub_Type_Code is out of setup range. 

0033h 

•  Cyclic data (command_data1) is out of setup range 

Argument related 

0034h 

•  Feedforward data (Command_Data3, Sub_Command_Data2/3) is out of setup range. 

0041h 

•  Write access is attempted to read only media. 

0042h 

•  Alarm clear command is executed while an alarm that cannot be cleared and no warning is issued. 

0043h 

•  Feedback scale error clear command is executed no feedback scale error is detected. 

0045h 

•  In servo on state, reset command is executed in attribute C parameter validation mode. 

Not executable 1 
(general) 

0046h 

•  After deceleration and stop according to the drive inhibit input (POT/NOT), direction command 

POT/NOT is applied. 

•  During deceleration according to the drive inhibit input (POT/NOT), a profile operation (except for 

Type_Code = 31h, 32h, 33h,34h,35h) is started. 

0051h • 

Maker 

use 

0052h 

•  During cyclic position control (CP) in absolute mode (absolute scale), Type_Code = 1

h of homing 

command (

4h) has been executed. 

•  During profile position control (PP) in absolute mode (absolute scale), profile homing has been executed.

0053h 

•  During cyclic position control (CP) in absolute mode (absolute scale), actual position set/command 

position set (Type_Code = 21h, 22h) of homing command (

4h) have been executed. 

0057h 

•  Return-to-home command, Type_Code = 1

h, is executed while in the servo-off condition. 

0058h 

•  While the external input is not assigned to the latch correct terminal, Type_Code is executed by using the 

external input as a trigger. 

0059h 

•  During profile position latch positioning/profile homing (Type_Code = 12h, 13h, 31h, 32h, 33h,34h,35h), 

homing command (

4h) has been executed. 

•  During profile positioning/profile continuous movement (Type_Code = 10h, 11h, 20h) homing command 

(

4h) of initialization mode (Type_Code=1

h, 31h) has been executed. 

Not executable 2 
(Related to 
return-to-home) 

005Ah 

•  Z phase is set to latch trigger signal despite absolute scale. 

Not executable 3 
(related to hardware 
factor) 

0061h 

•  “EEPROM writing” is not permitted because of under voltage of the control power 

0101h 

•  In processing the previous command 

0103h 

•  Command is not permitted to be accepted because the servo driver is accessing to the feedback scale now

Not executable 4 
(in process) 

0104h 

•  Type_Code has been changed while operating under profile position control (PP). 

Not executable 5 
(access inhibit) 

0201h 

•  Command is not permitted to be accepted because parameter writing or writing to EEPROM is inhibited 

now 

•  Write parameter command or write EEPROM command is issued while bit 0 of Pr.7.23 (RTEX function 

expansion setup 2) is set at 1. 

 

2.0

2.0

2.0

2.0

2.0

2.0

2.0

2.0

Содержание MINAS-A5NL Series
















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды