Panasonic KX-NS300 Скачать руководство пользователя | Manualshive

Страница: 45 / 752

background image

A

•

With the new card installed, does the total number of extensions or trunks exceed the maximum
supported by the PBX?

•

Is the type of card installed in the slot different from the card type set as "Pre-Install" for that slot?
Confirm that the correct card is installed in the slot.

•

Is the card firmly and fully installed in the slot? Confirm that the card is installed correctly in the
slot.

•

Confirm that the card is not damaged.

Q

I cannot change an LCO port to INS status.

A

•

Is the card installed in the appropriate slot?

•

Is the card installed in the correct slot, but not functioning correctly?
Check the condition of the card.

•

Is the card itself in INS status?
Set it to INS status.

•

Is a trunk line connected to the appropriate port?

•

Is the port in FAULT status, even though a trunk is connected?
Run diagnosis on the relevant slot.

Q

How do I prevent newly installed cards automatically being changed to "INS"?

A

•

Change

New Card Installation—Card Status for any Card

in

9.36 PBX Configuration—[1-3]

Configuration—Option

from "In Service (INS)" to "Out of Service (OUS)".

Portable Stations

Q

I cannot register Portable Stations using the method described in 9.35 PBX Configuration—
[1-2] Configuration—Portable Station.

A

•

Do the PINs (Personal Identification Numbers) of the PBX and the Portable Station match?
Confirm that they are the same.

•

Is the Portable Station within transmission range of the CS?

•

Has the Portable Station previously been registered at another location?
It is not possible to register a Portable Station at 2 locations, so use the

Forced De-registration

option to delete the previous registration.

Q

I cannot delete the extension number of a Portable Station.

A

•

First, de-register the Portable Station itself, and then delete the extension number.

Q

I cannot de-register a Portable Station.

A

•

Is the Portable Station turned on? If not, turn it on.

•

Is the Portable Station within transmission range of the CS? If not, move it closer to the CS and
try the de-registration operation again.

Q

The Portable Station I want to de-register is broken, and will not turn on, or is not available,
or the registration information was deleted first from the Portable Station, so it cannot be de-
registered.

A

•

The Portable Station can be forcibly de-registered by following the procedure shown in

Forced

De-registration

9.35 PBX Configuration—[1-2] Configuration—Portable Station

.

2.3 Frequently Asked Questions (FAQ)

PC Programming Manual

45

«
...
43
44
45
46
47
...
»

Содержание KX-NS300

















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-NS300

Бренд: AGFEO Страницы: 28

Бренд: AGFEO Страницы: 28

Бренд: AGFEO Страницы: 220

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды