Panasonic KX-FP362BX Скачать руководство пользователя страница 61

Страница: 61 / 196

6.6.3. TROUBLESHOOTING ITEMS TABLE

ITEM

SYMPTOM

REFERENCE

ADF

(Auto Document Feeder)

The document does not feed.

NO DOCUMENT FEED (P.62)

Document jam

DOCUMENT JAM (P.63)

Multiple feed

MULTIPLE FEED (P.64)

Skew

SKEW (P.65)

Recording paper feed

The recording paper does not feed.

THE RECORDING PAPER DOES NOT FEED (P.66)

Paper jam

PAPER JAM (P.67)

Multiple feed and skew

MULTIPLE FEED AND SKEW (P.68)

Printing

The sent fax data is skewed.

THE SENT FAX DATA IS SKEWED (P.68)

The received fax data is skewed.

THE RECEIVED FAX DATA IS SKEWED (P.68)

The received or copied data is expanded.

RECEIVED OR COPIED DATA IS EXPANDED (P.69)

A blank page is copied.

A BLANK PAGE IS COPIED (P.62)

A blank page is received.

A BLANK PAGE IS RECEIVED (P.72)

Black or white vertical line

BLACK OR WHITE VERTICAL LINE (P.72)

Black or white lateral line

BLACK OR WHITE LATERAL LINE ON PRINT OUT (P.73)

An abnormal image is printed

AN ABNORMAL IMAGE IS PRINTED (P.74)

Communication

FAX, TEL

(analog board)

Cannot communicate by fax.
An error code is displayed.

See COMMUNICATION SECTION (P.75)

Cannot talk.
The DTMF tone doesn’t work.
The handset / monitor doesn’t work, etc.

See ANALOG BOARD SECTION (P.105)

Operation panel

Keys are not accepted.

See OPERATION PANEL SECTION (P.112)

Sensor

If the electric circuit is the cause, the error
message corresponding to the sensor will be
displayed.

See SENSOR SECTION (P.113)

6.6.3.1. SIMPLE CHECK LIST

SERIAL NO.

DATE

FUNCTION

JUDGEMENT

REFERENCE

FAX operation

Transmission

OK / NG

Receiving

OK / NG

Copy operation

OK / NG

Telephone operation

Handset transceiver / receiver

OK / NG

Digital SP-PHONE sound

OK / NG

Ringer sound

OK / NG

Dial operation

OK / NG

Volume operation

OK / NG

VOX detection

OK / NG

Service code #815 (Refer to TEST FUNCTIONS (P.50))

Operation Panel

Key check

OK / NG

Service code #561 (Refer to TEST FUNCTIONS (P.50))

LED check

OK / NG

Service code #557 (Refer to TEST FUNCTIONS (P.50))

LCD check

OK / NG

Service code #558 (Refer to TEST FUNCTIONS (P.50))

Sensor

Sensor check

OK / NG

Service code #815 (Refer to TEST FUNCTIONS (P.50))

Clock

Display changing

OK / NG

Is the time kept correctly?
Check with another clock.

Digital TAM

Greeting REC / PLAY

OK / NG

Incoming message REC / PLAY

OK / NG

Memo REC / PLAY

OK / NG

Voice prompt

OK / NG

Service code #784
Check whether voice prompt is play or not.

KX-FP362BX

Содержание KX-FP362BX





































































































































































































Результаты поиска

Содержание KX-FP362BX

Отзывы:

Похожие инструкции для KX-FP362BX

Бренды по названию

Популярные бренды

Panasonic KX-FP362BX, Руководство по обслуживанию

Результаты поиска

Содержание KX-FP362BX

Отзывы:

Похожие инструкции для KX-FP362BX

Бренды по названию

Популярные бренды