Panasonic KX-FP362BX Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 196

background image

When set to ON (=1), the 12 keys and transmission
frequencies are as shown.

key

High Frequency (Hz)

key

Low Frequency (Hz)

“1”

697

“5”

1209

“2”

770

“6”

1336

“3”

852

“7”

1477

“4”

941

“8”

1633

When set to OFF (=2), the 12 keys and transmission
frequencies are as shown.

High (Hz)

1209

1336

1477

Low (Hz)
697

“1”

“2”

“3”

770

“4”

“5”

“6”

852

“7”

“8”

“9”

941

“

”

“0”

“#”

Test Mode

Type of Mode

Code

Function

Operation after code

input

SENSOR CHECK &
VOX CHECK

Service Mode

“8” “1” “5”

If you enter this mode and operate sensor levers with your hands, the LCD
display of the related sensor (or switch) turns ON / OFF. Also, when copying a
document, the related sensor will turn ON / OFF. ( Do, Sn, Co, Pt, Vx)
For each sensor’s operation, refer to SENSORS AND SWITCHES(P.137).

Do Sn Co Pt Vx

: LCD DISPLAY

Do: Document set sensor

:Paper inserted. Turns on when a document is inserted.

Sn: Read position sensor.

:At the read position, turns on when the front cover is opened and the
sensor lever is pressed directory.

Co: Cover open sensor / Film end sensor

:Cover open of don’t set the film. Turns on and off when the front cover is
opened and closed.

Pt: Paper top sensor

:Sensor on Turns on when the front cover is opened and the sensor lever
is pressed directly.

Vx: Vox signal

:Detection signal for the tone on the line. Turns on when there is a tone
signal on the line.

START

Note:

The numbers in the boxes (XXX) indicate the keys to be input for the various test modes.

6.3.1. DTMF SINGLE TONE TRANSMIT SELECTION

Note:

After performing this check, do not forget to turn the setting off.

Otherwise, dialing in DTMF signal will not work.

6.3.2. BUTTON CODE TABLE

Code

Button Name

Code

Button Name

Code

Button Name

Code

Button Name

04

FAX /START / SET

31

1

3C

#

64

STATION 1

05

LOWER

32

2

3D

REDIAL PAUSE

65

STATION 2

06

COPY

33

3

3E

FLASH

66

STATION 3

08

DIGITAL SP-PHONE

34

4

47

SEARCH

67

STATION 4

0A

MUTE

35

5

4E

JUNK FAX PROHIBOTOR

68

STATION 5

0C

AUTO ANSWER

36

6

1E

NEXT

14

RECORD

37

7

1F

PREV

16

ERASE

38

8

18

PLAY MESSAGE

39

9

00

NO INPUT

20

MENU

3A

0

01

STOP

22

HELP

25

[+] VOLUME

26

[-] VOLUME

51

KX-FP362BX

«
...
49
50
51
52
53
...
»

Содержание KX-FP362BX





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-FP362BX

Бренд: Fellowes Страницы: 7

Бренд: Fellowes Страницы: 8

Бренд: Fellowes Страницы: 8

Бренд: Baby Lock Страницы: 212

Бренд: Fastbind Страницы: 21

Бренд: Ricoh Страницы: 116

Бренд: Cameo Страницы: 40

Бренд: Truvox Страницы: 12

Бренд: Kärcher Страницы: 12

Бренд: ROOTS Страницы: 164

Бренд: Bernina Страницы: 134

Бренд: Garudan Страницы: 67

Бренд: Singer Страницы: 67

Бренд: JUKI Страницы: 59

Бренд: Singer Страницы: 48

Бренд: Canon Страницы: 2

Бренд: JUKI Страницы: 136

Бренд: soundsation Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды