Panasonic KX-FP362BX Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 196

background image

6.4. REMOTE PROGRAMMING

If, after the call is connected, the customer describes the situation and it is determined that the problem can be corrected by
making parameter changes, this function makes it possible to change parameters such as the user code and service code from
another fax (using DTMF tones). Therefore, travel to the customer´s location is not required. However, it is not possible to
change all the parameters remotely (PROGRAM MODE TABLE (P.54)). The function used to accomplish this is remote
programming.

First, in order to check the current status of the service code parameter, print out the setup list (code: 991) and the service list
(code: 999) from the customer´s fax machine.

Based on this, the parameters for the desired codes can be changed.

The procedure for changing and listing parameters is described on ENTERING THE REMOTE PROGRAMMING MODE AND
CHANGING SERVICE CODES (P.53). Also, before exiting the remote programming mode, it is advisable to obtain a new list
to confirm that the changes were made correctly.

Hint:

Since the connected telephone is in use during the remote programming mode, it may be helpful to ask the customer to switch
to the speakerphone. This frees the customer from the need to remain right next to the fax while you are making parameter
settings. When finished, inform the customer. Also note that in very noisy locations where the DTMF tones are not audible, the
remote programming function will not work.

6.4.1. ENTERING THE REMOTE PROGRAMMING MODE AND CHANGING SERVICE

CODES

CROSS REFERENCE:

PROGRAM MODE TABLE (P.54)

53

KX-FP362BX

«
...
51
52
53
54
55
...
»

Содержание KX-FP362BX





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KX-FP362BX

Бренд: Makita Страницы: 5

Бренд: Fellowes Страницы: 9

Бренд: Fellowes Страницы: 5

Бренд: Fellowes Страницы: 6

Бренд: Fellowes Страницы: 4

Бренд: Fellowes Страницы: 76

Бренд: Fellowes Страницы: 6

Бренд: Fellowes Страницы: 8

Бренд: Fellowes Страницы: 74

Бренд: Duerkopp Adler Страницы: 35

Бренд: VeriFone Страницы: 40

Бренд: Singer Страницы: 54

Бренд: Truvox Страницы: 12

Бренд: DURKOPP ADLER Страницы: 338

Little Misty LM-1

Бренд: Talent Страницы: 6

Бренд: MAGMATIC Страницы: 20

Бренд: Pfaff Страницы: 30

Бренд: Nobles Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды