Panasonic KX-F1000AL Скачать руководство пользователя

Страница: 7 / 88

1. Installation and Connection

Installing the batteries

(KX-F1100AL only)

The batteries are required to retain greeting and incoming voice messages in memory when the power cord is
disconnected or during a power failure. Install four AA batteries (supplied) before using the unit.

Open the top cover, then open the front lid by
sliding the lever towards you.

Remove the battery compartment cover by
pulling the hook towards you and lifting it up.

Install four batteries into the compartment
using correct polarity (+, –).

Replace the battery compartment cover by;

Insert the tab of the cover into the hole.

Press down the area marked “PRESS”
until it clicks into place.

Close the front lid securely by pushing down
on both sides, then close the top cover.

PRESS

Note:

Message retention time during a power failure is approximately 1 day with new batteries.

Install new batteries when the display shows “BATTERY LOW”.

To avoid losing the greeting and all messages saved in memory, the power cord must remain connected
when replacing batteries.

Disconnect the telephone line cord before opening the battery compartment cover.

Replace all the batteries once a year, or mis-operation may occur.

For further information about batteries, see page 81.

PRESS

Front lid
open lever

Front lid

Top cover

Содержание KX-F1000AL

























































































Результаты поиска

Содержание KX-F1000AL

Отзывы:

Похожие инструкции для KX-F1000AL

Бренды по названию

Популярные бренды

Panasonic KX-F1000AL, Руководство по эксплуатации

Результаты поиска

Содержание KX-F1000AL

Отзывы:

Похожие инструкции для KX-F1000AL

Бренды по названию

Популярные бренды