Panasonic KV-S1025C SERIES Скачать руководство пользователя

Страница: 8 / 117

Note:

: KV-S1020C Series

KV-S1020C: for USA

    KV-S1020C-G: for German
    KV-S1020C-U: for UK
    KV-S1020C-R: for Russia
    KV-S1020C-K: for Korea
    KV-S1020C-A: for Australlia
    KV-S1020C-CN: for China

KV-S1020C-T: for Taiwan

SERIAL No. shown on the name plate on each scanner will distinguish the destinations for each area as follows.

1. SERIAL No. for USA

→

864 xxxx xxxx

2. SERIAL No. for German

→

867 xxxx xxxx

3. SERIAL No. for UK

→

865 xxxx xxxx

4. SERIAL No. for Russia

→

868 xxxx xxxx

5. SERIAL No. for Korea

→

869 xxxx xxxx

6. SERIAL No. for Australlia

→

866 xxxx xxxx

7. SERIAL No. for China

→

870 xxxx xxxx

8. SERIAL No. for Taiwan

→

871 xxxx xxxx

(x: Don't care)

: Applied to KV-S1020C for USA and other countries where power supply (AC100 to 120 V) is used

: Applied to KV-S1020C-G/-U/-R/-K/-A/-CN for German, UK, Russia, Korea, Australlia, China, and other countries where

power supply (AC220 to 240 V) is used.

: The scanning speed depends on the test environment. In addition, it differs depending on the host computer operating

environment or applications.

: MultiStream is registered trademark or trademark of EMC Corporation.

Содержание KV-S1025C SERIES






















































































































Результаты поиска

Содержание KV-S1025C SERIES

Отзывы:

Похожие инструкции для KV-S1025C SERIES

Бренды по названию

Популярные бренды

Panasonic KV-S1025C SERIES, Руководство по обслуживанию

Результаты поиска

Содержание KV-S1025C SERIES

Отзывы:

Похожие инструкции для KV-S1025C SERIES

Бренды по названию

Популярные бренды