Panasonic KV-S1025C SERIES Скачать руководство пользователя | Manualshive

Страница: 65 / 117

background image

65

9.3.

Operation

This section describes each operation (or status indication), according to the function item list shown in Sec. 9.2.

9.3.1.

Scanner Status

This function indicates the scanner status, updating it every few seconds.
The status messages and their contents are as follows.

Fig. 9.3.1 Scanner Status

Classified Code

Status Message

Contents

—

Scanner has no error.

No error

U11/ U16/ U23

A paper jam or double feed has occurred.
Open the scanner’s door, remove the
documents, and close the door.
Place the documents back in the document
feed tray.

Paper jam or double feed error

U18

Paper remains in the scanner.
Open the scanner’s door, remove the
documents, and close the door.
Place the documents back in the document
feed tray.

Document remains in the scanner, there is
dust around a sensor, or the sensor
arm does not work properly.

U30

Scanner Door is open!
Please close the door.

ADF Door is open, or does not close tightly.
Or the door detection mechanism does not
work properly.

Fxx

System error occurred!
Please consult with a service representative.

This type of error code requires a
Service-person's attention.

—

No Paper!
Please set the paper.

No paper error

—

The rollers need to be cleaned.
Please clean the rollers.
Please select “Clear Counter” button after
cleaning the rollers.

Warning for cleaning the rollers

—

The Double-feed Prevention Roller
(consumable) is reaching the end of their
usable life. To insure reliable operation,
please replace this roller with Roller
Exchange Kit for your specific scanner.
After replacing the roller, select the “Clear
Counter” button.

Warning for replacing the Double-feed
Prevention Roller

—

The Paper Feed Roller (consumable) is
reaching the end of their usable life.
To insure reliable operation, please replace
this roller with Roller Exchange Kit for your
specific scanner.
After replacing the roller, select the “Clear
Counter” button.

Warning for replacing the Paper Feed
Roller

—

Scanner is not connected!

Scanner is not connected to the PC
properly.

«
...
63
64
65
66
67
...
»

Содержание KV-S1025C SERIES






















































































































Отзывы:

Нет отзывов

Похожие инструкции для KV-S1025C SERIES

Бренд: Uniden Страницы: 35

Dimage Scan Elite F-2900

Бренд: Minolta Страницы: 40

Бренд: Olympus Страницы: 266

Бренд: Radio Shack Страницы: 40

Бренд: i.safe MOBILE Страницы: 76

Бренд: Clas Ohlson Страницы: 73

Бренд: Avision Страницы: 43

Бренд: Avision Страницы: 45

Бренд: Avision Страницы: 2

Бренд: Avision Страницы: 31

Бренд: Avision Страницы: 96

Бренд: Avision Страницы: 106

Бренд: NEXPEAK Страницы: 83

Бренд: Allflex Страницы: 44

Бренд: Di-soric Страницы: 222

Бренд: Plustek Страницы: 31

eScan SharePoint

Бренд: Plustek Страницы: 2

Бренд: polyga Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды