32
CY-VHD9500U
CY-VHD9500U
33
Installation
(continued)
E
N
G
L
I
S
H
13
E
N
G
L
I
S
H
14
Note:
≥
Be careful not to scratch the surface of the
front cover when removing it.
≥
The screws you remove now will be needed
when you re-attach it to complete installation.
Keep them in a place where they will not be
lost.
Caution:
≥
Before installing the unit, be absolutely
sure to check that the screws do not
make any contact with the ceiling panel.
If some space is required between the
base plate and the unit, attach and adjust
the under cover (see next page). For
details on installing the under cover,
consult your dealer.
2
Insert the screws (
6
), space washers A, B,
or C (
>
,
?
, or
@
), fl at/spring washers (
9
and
:
), and push nuts (
8
) in the main unit.
Keep the screws only loosely tightened until the
unit is attached to the base plate.
A
A
A
8
Push nuts
(No. 10-32 UNF)
:
Flat washer
[No. 10 (5 mm
‡
)]
9
Spring washer
[No. 10 (5 mm
‡
)]
6
Screw
[No. 10-32 UNF, L=1
1
/
4
q
(32 mm)]
Front cover
6
Screw
a
6
9
Spring washer
a
6
:
Flat washer
a
6
8
Push nuts
a
6
>
or
?
or
@
Space washer*
(A or B or C)
a
6
* Depending on the type of vehicle for the
installation, you may not need to use
some space washers. When the space
washers are to be used, make absolutely
sure that their height will be the same in
all 6 locations. Consult your dealer for
details.
1
Insert the screws (
C
), space washers D (
B
),
fl at/spring washers (
9
and
:
), and push nuts
(
8
) in the main unit and attach the base plate.
Caution:
≥
Before installing the unit, be absolutely
sure to check that the screws do not
make any contact with the ceiling panel.
2
Use the screws (for resin) (
D
) to attach the
accessory under cover (
A
) to the underside of
the main unit.
ª
If some space is required between the base plate and the unit, attach the under cover
and adjust as follows.
4
Get ready to attach the main unit.
B
Space washer (D)
[t=31
1
/
4
q
(80 mm)]
8
Push nuts
(No. 10-32 UNF)
:
Flat washer
[No. 10 (5 mm
‡
)]
9
Spring washer
[No. 10 (5 mm
‡
)]
C
Screw
[No. 10-32 UNF, L=4
q
(100 mm)]
Unit
D
Screw
[
1
/
10
q
(2.6 mm)
‡
k
8
/
25
q
(8 mm)]
a
6
A
Under
cover
Note:
≥
Depending on the type of vehicle, there
may be differences in the gap between the
headliner and the main unit. For gaps, adjust
the under cover and screw as necessary.
1
Open the display unit and remove the two
screws.
Place your fi ngers at A (in 2 places) on the
panel, and slowly pull down the panel.
>
or
?
or
@
Space washer*
A [t=
1
/
25
q
(1 mm)] or
B [t=
2
/
25
q
(2 mm)] or
C [t=
3
/
25
q
(3 mm)]
a
6
