16
CY-VHD9401U/L
CY-VHD9401U/L
17
No.
Item
Diagram
Q’ty
=
Space washer (A)
[t=1 mm {
1
/
25
q
}]
6
>
Space washer (B)
[t=2 mm {
2
/
25
q
}]
6
?
Space washer (C)
[t=3 mm {
3
/
25
q
}]
6
@
Under cover
1
A
Space washer (D)
[t=80 mm {3
3
/
16
q
}]
6
B
Screw [No. 10-32 UNF,
L=100 mm {4
q
}]
6
C
Screw (for resin)
[2.6 mm {
1
/
10
q
}
‡k
8 mm {
8
/
25
q
}]
6
Installation Guide
E
N
G
L
I
S
H
3
E
N
G
L
I
S
H
4
Overview
Your fi rst step is to decide where to install it. The
instructions in these pages will guide you through
the remaining steps:
(Please refer to the “WARNING” statement.)
≥
Identify and label the car wires.
≥
Connect the car wires to the wires of the power
connector.
≥
Install the unit.
≥
Check the operation of the unit.
If you encounter problems, please consult your
nearest professional installer.
Before you begin installation, look for the items
which are packed with your unit.
≥
Warranty Card
... Fill this out promptly.
≥
Panasonic Servicenter List for Service
Directory
... Keep for future reference in case the
product needs servicing.
≥
Installation Hardware
... Needed for installation.
WARNING:
≥
Use in DC 12 V
-
ground vehicles. This
product is only for DC 12 V
-
grounded
vehicles. It cannot be used in DC 24 V
vehicles (such as large trucks, diesel
vehicles designed for cold climates, etc.).
Using this product in such vehicles could
cause fi re or other malfunction.
≥
Be sure to disconnect the battery’s
-
terminal while wiring and installing the
product. Doing the wiring and installation
with the battery’s
-
terminal still connected
could cause electrical shock and injury due
to a short circuit accidents.
≥
Contact your car dealer or manufacturer
to determine the required procedure
and strictly follow their instructions
before attempting installation of this
product if your car is equipped with
air bag and/or anti-theft systems.
Specifi c procedures may be required for
connection and disconnection of the battery
to install this product. Failure to follow the
procedure may result in the unintended
deployment of air bags or activation of the
anti-theft system resulting in damage to the
car and personal injury.
Note:
≥
Various settings that have been stored in the
memory in other on-board equipment (car
navigation etc.) may be lost if the battery
terminals are disconnected.
Therefore, we recommend to make a record of or
to back up the settings before disconnecting the
terminals.
After completing installation of the main unit, set
the equipment again according to the record.
12 V DC
Test bulb
Electrical tape
Side-cut
pliers
Required Tools
You’ll need a screwdriver, and the following:
≥
Tools, cutter knife, cloth pieces are required for
the instructions.
≥
Use the tools of proper size to secure the bolts,
nuts and screws certainly.
Supplied Hardware
No.
Item
Diagram
Q’ty
1
Paper template
1
2
Slide plate (upper)*
1
3
Slide plate (lower)*
1
4
Base plate
1
5
Screw [No. 10-32 UNF,
L=10 mm {
3
/
8
q
}]
12
6
Screw [No. 10-32 UNF,
L=32 mm {1
1
/
4
q
}]
6
7
Nuts
(No. 10-32 UNF)
12
8
Push nuts
(No. 10-32 UNF)
6
9
Spring washer
[No. 10 (5 mm
‡
)]
6
:
Flat washer
[No. 10 (5 mm
‡
)]
6
;
Power connector
1
<
Cord clamp
2
ª
For Installation
* The upper slide plate and lower slide plate can
be distinguished as follows: only the upper
slide plate has line “A” and “B” stamped on it
(page 23).
