Panasonic AFP7CPS4E Скачать руководство пользователя страница 87

Страница: 87 / 139

8.3 MODBUS RTU Master Communication (RECV)

8-5



Timing chart

Confirm OFF

Execute RECV

Master communication

Sending active flag

(YC, YD, YE, YF)

Master communication

Sending done result flag

(Y0, Y1, Y2, Y3)

Sending data

Response reception

processing

Master communication

Clear to send flag

(XC, XD, XE, XF)

Confirm ON

Conditions to enable execution of RECV
instruction
Clear to send flag (XC, XD, XE, XF): ON
Sending active flag (YC, YD, YE, YF): OFF

Sending done result flag (Y0, Y1, Y2, Y3):
Normal completion: OFF
Abnormal completion: ON

Sending active flag (YC, YD, YE, YF):
Sending data: ON, Sending done: OFF



I/O allocation (For CPU Unit)

COM port no.

Name

Explanation

XC XD XE

Master
communication
Clear to send flag

Turns ON when MEWTOCOL-COM, MEWTOCOL7, or
MODBUS-RTU is set for the communication mode, and the unit is
in the RUN mode.

YC YD YE

Master
communication
Sending active flag

Turns ON during sending data based on SEND/RECV instruction.
Turns OFF when the sending process is completed.

Y0 Y1 Y2

Sending done
result flag

Reports completion result of sending data in general-purpose
communication or master communication. (Normal completion: 0,
Abnormal completion: 1)



I/O allocation (For Serial Communication Unit)

COM port no.

Name

Explanation

XC XD XE XF

Master
communication
Clear to send flag

Turns ON when MEWTOCOL-COM, MEWTOCOL7, or
MODBUS-RTU is set for the communication mode, and the
unit is in the RUN mode.

YC YD YE YF

Master
communication
Sending active flag

Turns ON during sending data based on SEND/RECV
instruction.
Turns OFF when the sending process is completed.

Y0 Y1 Y2 Y3

Sending done result
flag

Reports completion result of sending data in genera-purpose
communication or master communication.
(Normal completion: 0, Abnormal completion: 1)

(Note 1) Each contact is used for reading the operation status. Do not write over it with a user program.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Содержание AFP7CPS4E












































































































































Результаты поиска

Содержание AFP7CPS4E

Отзывы:

Похожие инструкции для AFP7CPS4E

Бренды по названию

Популярные бренды

Panasonic AFP7CPS4E, Руководство пользователя

Результаты поиска

Содержание AFP7CPS4E

Отзывы:

Похожие инструкции для AFP7CPS4E

Бренды по названию

Популярные бренды